Hoppe

Part Number: S4010 Before you place your order please read all below watch our video at the bottom of the product page to make sure you order the correct hinge.  S4010 HTL Ultimate 2-D Hinge - Hoppe Guide Hinge Horizontal Adjustment - Non Handed -  Removable Pin Style No Screws Included  Color / Finish Options Are as Follows:  Bright Brass  Polished Chrome Rustic Umber  Stainless Steel  Matte Black White  Antique Brass, Brushed Chrome - NO LONGER AVAILABLE - Use part number S4012 as direct replacement hinge. When factory discontinues a color for S4010 use S4012 as the direct replacement hinge.  Product Description:  S4010 is a Guide Hinge - Horizontal adjustment only . Comes in multiple finishes S4010 works in tandem with S4009 sold separately. See hinge guide placement in pictures  Steel Reinforcements – Makes this new hinge the "Ultimate" with door systems.• Corrosion Resistant – Specially coated components for improveddurability and strength.• Easy Adjustment – Set hinge is Part # S4009 sold separately has a vertical adjustment feature (+/- 2.5mm). S4009 works in tandem with S4010. Guide hinge (Part # S4010) has a horizontal adjustment feature (+/- 2mm). See hinge placement diagram in pictures. • Maintenance Free Bearings – No oiling required.• Simple Door Preparation – Quick and easy one pass routing.• Variety of Finishes – Available in finishes to match your HOPPE® handle sets.• Designed to carry up to 165lbs. per door.• Not to be used in commercial applications, especially not inconjunction with a door closer. Set and Guide Hinge Placement:  3 Hinges Per Door Panel:  Starting at top of door Top of door Guide (S4010) Set (S4009)  Guide (S4010) 4 Hinges Per Door Panel: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide (S4010) Guide (S4010   Set (S4009) Guide (S4010)  The Set hinge no matter what is always the 2nd from the bottom Pro Tips: These hinges are not handed! The pin is removable So you can reverse the handing for your door . (Scroll thru pictures above that show this) Pin can be tight - use a flat head screw driver and hammer to LIGHTLY tap out the pin from the bottom. Remove weight from the hinges by lifting up on the door before you adjust.  Never use power tools to adjust the hinge. ONLY use hand tools.  Hinge: S4010 Minimum of two per panel. These hinges only have the horizontal adjustment ± 2mm. When the vertical adjustment (S4009) is turned clockwise, the non-adjustable leaf will move in the direction of the arrow. The vertical adjustment has 32 turns from it's extremes, and the horizontal (s4010) has 7 turns. Adjust the horizontal by turning clockwise to increase the margins. Turn counter clockwise to decrease the margins Known Part # 850-8762435,  850-8762531, Pat.Nr. 5.701.636, 30033, 8762531, 5 310544 0 10708

Read more less

Part Number: S4009 Before you place your order please read below and watch our video at the bottom of the product page to make sure you are ordering the correct hinge. Hoppe HTL Ultimate 2-D Hinge - Hoppe Set Hinge (vertical adjustment) - Removable Pin Style These SET HINGES ARE NOT HANDED - you can remove the pin to swap the handing for your door. (For NON-Removable pin style see Part # S4011 and they ARE HANDED, if any of the S4009 become unavailable you will need to order S4011) No Screws Included, sold individually  Material: Steel Color / Finish Options Are as Follows:  Bright Brass  Polished Chrome Rustic Umber  Matte Black (available for pre-order will not be receiving more in till mid October 2023, no order cancellation - thank you for your patience).  Stainless Steel  White  Antique Brass, Brushed Chrome - NO LONGER AVAILABLE once stock is gone See part number S4011 direct replacement hinge We stock these hinges- if you would like a QTY check on a color please e-mail or text us. Product Description:  S4009 is a Set hinge- vertical adjustment only . Comes in multiple finishes. Pin is removable. S4009 works in tandem with S4010 sold separately. See hinge placement diagram in pictures and watch video below. Steel Reinforcements – Makes this new hinge the "Ultimate" with door systems. • Corrosion Resistant – Specially coated components for improved durability and strength. • Easy Adjustment – Set hinge (Part # S4009) has a vertical adjustment feature (+/- 2.5mm) Guide hinge (Part # S4010 sold separately ) has a horizontal adjustment feature (+/- 2mm) and works in tandem with S4009 see hinge placement description below and diagram in pictures. • Maintenance Free Bearings – No oiling required. • Simple Door Preparation – Quick and easy one pass routing. • Variety of Finishes – Available in finishes to match your HOPPE® handle sets. • Designed to carry up to 165lbs. per door. • Not to be used in commercial applications, especially not in conjunction with a door closer.   Set and Guide Hinge Placement (see picture diagram): 3 Hinges Per Door Panel: Starting at top of door Top of door Guide (use part # S4010) Set (use part # S4009) Guide (use part # S4010)   4 Hinges Per Door Panel (see picture diagram): Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide (use part # S4010) Guide (use part # S4010)  Set (use part # S4009) Guide (use part # S4010) The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Pro Tips: Remove weight from the hinges by lifting up on the door before you adjust.  Never use power tools to adjust the hinge. ONLY use hand tools.  Hinge S4009- 1 hinge per panel. Vertical adjustment  feature (+/- 2.5mm) When the vertical adjustment (S4009) is turned clockwise, the non-adjustable leaf will move in the direction of the arrow. The vertical adjustment has 32 turns from it's extremes, and the horizontal (s4010) has 7 turns. Adjust the horizontal by turning clockwise to increase the margins. Turn counter clockwise to decrease the margins Known Part # 850-8762439 and Pat. Nr. 5701636, Pat. Nr. 5,701,636  

Read more less

Part Number: S4011 - SET Hinge Hoppe Adjustable Door Hinge Non Removable Hinge - Set Hinge Vertical Adjustment  S4011 is Vertical Adjustment ONLY Watch video and read instructions in pictures (For Horizontal adjustment see part number S4012 Sold Separately and see hinge placement guide in picture) No Screws Included, sold individually  Handing: Left Hand Hinge Used For: Left Hand In swinging (LHI) or Right Hand Out Swinging (RHO) Right Hand Hinge Used For: Right Hand In Swinging (RHI) Left Hand Out Swinging (LHO) SEE  Hoppe "Application Diagram for Set Hinge” TO DETERMINE WHAT HANDING HINGE TO ORDER Pre-Order are Special order items, no returns  Made out of Brass or Aluminum. Multiple finishes to choose from.  Designed for a Greater Advantage • Adjusts vertically ( Use Set Hinge Part # S4011) and  for horizontally ( see Guide Hinge Part # S4012) by 1/8" for a perfect swing. - see Installation Instructions page 1 number of hinges chart for application. • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish.  Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012)  Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012)   Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012) Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012)  The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known to have been used on: Sierra Pacific Doors, Ashworth and many other

Read more less

Part Number: S4014 S4014 Hoppe Millennium Adjustable Hinge - 2-D Guide Hinge with Non-removable Pin Horizontal Adjustment  - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors Colors Still Available: Stainless Steel  Discontinued Colors: Oil Rubbed Bronze, Antique Brass, Brass, Brushed Chrome Pat.Nr. 5.701.636 122190600, 850-8754743 Set and Guide Hinge Placement: 3 Hinges Per Door Panel - Up to 165 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel -Up to 165 lbs: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel - 165 - 330 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 5 Hinges Per Door Panel - 165 to 330 lbs: Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known part # 850-8754731, 850-8754743,122190600  General HOPPE Adjustable Hinge Adjustment Instructions: Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above. Prepare the door panel and frame. Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed. On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening. Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges. Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout. Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge. Disassembly Do not attempt to remove the hinge pin, as this may cause damage. To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges. Carefully remove either the frame leaf screws or door leaf screws to displace the panel. Adjustment Instructions Introduction There are two types of HOPPE Adjustable Hinges on each door panel: Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment. Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge. Hinge designs may vary, but adjustment remains the same. Required Tools A 3/16” hex wrench is required. A small flat head screwdriver is required. A plastic putty knife is recommended. Vertical Adjustment for Doors with One Set Hinge With the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel. Reinstall the Finial Cap removed in Step 1. Vertical Adjustment for Doors with Two Set Hinges With the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. To raise the panel, insert the hex wrench into the top-most Set Hinge and tighten the adjustment screw to achieve the desired Insert the hex wrench into the other Set Hinge and tighten the adjustment screw 1/8 turn past the onset of resistance to distribute the panel weight evenly between both Set Hinges. To lower the panel, insert the hex wrench into the top-most Set Hinge and loosen the adjustment screw as far as possible without Insert the hex wrench into the other Set Hinge and loosen the adjustment screw to achieve the desired adjustment. Retighten the adjustment screw on the top-most 1/8 turn past the onset of resistance to distribute the panel weight evenly between both Set Hinges. Reinstall the Finial Caps removed in Step 1. Horizontal Adjustment With the door open: Insert a 3/16” hex wrench into the horizontal adjustment screw. Turn clockwise to decrease the margin and counterclockwise to increase the margin on the hinge side.

Read more less

Part Number:  S4012 – Guide Hinge Hoppe Adjustable Hinge - Guide Hinge - Non Removable Pin Style. S4012 is Horizontal Adjustment Only (Watch video and read instructions in picture's) No Screws Included, sold individually  GUIDE HINGES ARE NOT HANDED. Will work on both LH and RH Doors by how you mount the hinge If not in stock - Pre Order - Special order item - no return 3-8 week lead time  Made out of Brass or Aluminum. Multiple finishes to choose from.  Designed for a Greater Advantage • To Adjust vertically (Use Set Hinge Part # S4011) and  for horizontally (Use Guide Hinge Part # S4012) by 1/8" for a perfect swing. See Installation Set and Guide Hinge Placement • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish. Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012)  Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012)   Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012) Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012)  The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known to have been used on Sierra Pacific Doors and Ashworth

Read more less

 Part Number: S4013   Hoppe Millennium Adjustable Hinge - 2-D Set Hinge with Non-removable Pin Vertical Adjustment  - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors Colors Still Available: Stainless Steel Discontinued Colors: Oil Rubbed Bronze, Brass Chrome, antique brass Pat.Nr. 5.701.1636, 122210600   Set and Guide Hinge Placement Table: 3 Hinges Per Door Panel - Up to 165 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel -Up to 165 lbs: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel - 165 - 330 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 5 Hinges Per Door Panel - 165 to 330 lbs: Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known part # 850-2388803, 850-8754819, 122210600   General HOPPE Adjustable Hinge Adjustment Instructions: Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above. Prepare the door panel and frame. Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed. On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening. Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges. Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout. Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge. Disassembly Do not attempt to remove the hinge pin, as this may cause damage. To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges. Carefully remove either the frame leaf screws or door leaf screws to displace the panel. Adjustment InstructionsIntroductionThere are two types of HOPPE Adjustable Hinges on each door panel: Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment. Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge. Hinge designs may vary, but adjustment remains the same. Required Tools A 3/16” hex wrench is required. A small flat head screwdriver is required. A plastic putty knife is recommended. Vertical Adjustment for Doors with One Set HingeWith the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel. Reinstall the Finial Cap removed in Step 1. Vertical Adjustment for Doors with Two Set HingesWith the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hingeto expose the adjustment screw. Use the small screwdriver forSet Hinges featuring a plastic Finial Cap. A plastic putty knife isrecommended for Set Hinges featuring a brass Finial Cap. To raise the panel, insert the hex wrench into the top-most SetHinge and tighten the adjustment screw to achieve the desiredInsert the hex wrench into the other Set Hinge andtighten the adjustment screw 1/8 turn past the onset of resistanceto distribute the panel weight evenly between both Set Hinges. To lower the panel, insert the hex wrench into the top-most SetHinge and loosen the adjustment screw as far as possible withoutInsert the hex wrench into the other Set Hinge andloosen the adjustment screw to achieve the desired adjustment.Retighten the adjustment screw on the top-most 1/8 turn past theonset of resistance to distribute the panel weight evenly betweenboth Set Hinges. Reinstall the Finial Caps removed in Step 1. Horizontal AdjustmentWith the door open: Insert a 3/16” hex wrench into the horizontal adjustment screw. Turn clockwise to decrease the margin and counterclockwise toincrease the margin on the hinge side. IF THIS HINGE DOES NOT LOOK EXACTLY LIKE YOUR ADJUSTABLE HINGE. CLICK HERE TO SEE ALL THE ADJUSTABLE HINGES WE HAVE ON OUR WEBSITE TO ORDER. IF YOU ARE NOT FINDING YOUR HINGE PLEASE EMAIL OR TEXT OUR RESEARCH DEPARTMENT AND WE WOULD BE HAPPY TO ASSIST YOU

Read more less