Hoppe

7 products


  • Hoppe Vertical Adjustable Door Hinge - Set Hinge 122330200 850-8755047. Known to work on: Semco Doors, Hoppe Hardware, Hoppe Columbus, Windsor Doors and Superior Doors

    Hoppe S4001 Hoppe 2-D Vertical Adjustable Door Hinge DISCONTIUNED See Product Description for Replacement Option

    Out of stock

    Part Number S4001  Dual adjustment discontinued see part number S4003 and S4004 for replacement and more information and video below.  Hoppe Columbus 2-D Set Vertical Adjustment Hinge for Wood and Vinyl  S4001 Dual Adjustment Hinges HAS been discontinued and the replacement S4003 and S4004 The S4003 is a vertical adjustment hinge only see video below on how to adjust the S4003. For more information on the S4003 Vertical hinge click here. If you also need Horizontal adjustment you will also need to order part number S4004 guide hinge Click Here See hinge placement guide below or in the hinge placement drawing in pictures to know if you need to order the S4003, S4004 hinge or both. By having both the S4003 and s4004 hinge on your door you will be able to adjust it horizontally and vertically.  Hoppe 2-D Adjustable Door Hinge for Wood and Vinyl Products - Set Hinge Vertical Adjustment (+/- 3 mm)  Hinges are NON Handed - this hinge is for Left Hand and Right Hand Doors you can remove the hinge pin to change the handing for your door before you install. Set and Guide Hinge Placement - Also See Hinge Placement Guide Drawing: 3 Hinges Per Door Panel: Starting at top of door Top of door Guide (Part # S4004) Set (Part # S4003) Guide (Part # S4004) 4 Hinges Per Door Panel: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide (Part # S4004) Guide (Part # S4004)  Set (Part # S4003) Guide (Part # S4004) Manufacture  Information and Product Detail:  KTL Bright Alternative Shown in Picture Settling of walls and floors can make door panels hard to open and close. The 2-D Adjustable Hinge allows easy adjustment of the door both horizontally (+/- 2 mm Guide Hinge Part # S4004) and vertically (+/- 3 mm Set Hinge Part # S4003) with just the turn of a screw. Each hinge is reversible and has maintenance free bearings.  There are two types of adjustable hinges for each door panel A. Set hinge Part # S4003: One per panel. This has vertical adjustment  (+/- 3 mm). B. Guide Hinge Part # S4004: Minimum of two per panel. These hinges only have the horizontal adjustment (+/- 2 mm) Adjustment Instructions:  Normal hinge replacement has the set hinge. Using a Phillips screwdriver, first adjust the panel up or down by turning the screw marked "V" on the set hinge. When turning the screw in the direction of the arrow (counter clockwise) the other leaf will be pushed in the direction of the arrow. Automatic screwdrivers are NOT recommended. The speed of the gun may strip the heads of the screws are over adjusted.  When the vertical adjustment is turned clockwise, the non-adjustable leaf will move in the direction of the arrow. The vertical adjustment has 32 turns from its extremes, and the horizontal has 7 turns.  Adjust the horizontal by turning clockwise to increase margins, Turn counter clockwise to decrease the margins.  Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust. Never use power tools to adjust your hinge. Always use a hand screwdriver.   Known Parts Numbers 122330200, 850-8755047, Pat Nr. 5.701.636 Known to work on: Semco Doors, Hoppe Hardware, Hoppe Columbus, Windsor Doors, Loewen Doors and Superior Doors  *Finish Note: Not for Coastal or High Humidity Applications. These hinges do not come in a sea coast or stainless material, high humidity or costal application can cause hinges to corrade this is not a product defect. IF THIS HINGE DOES NOT LOOK EXACTLY LIKE YOUR ADJUSTABLE HINGE. CLICK HERE TO SEE ALL THE ADJUSTABLE HINGES WE HAVE ON OUR WEBSITE TO ORDER. IF YOU ARE NOT FINDING YOUR HINGE PLEASE EMAIL OR TEXT OUR RESEARCH DEPARTMENT AND WE WOULD BE HAPPY TO ASSIST YOU.  

    Out of stock

    $ 0.00

  • Hoppe 2-D Adjustable Door Hinge  - Guide Hinge Horizontal Adjustment. Part Number: 122340200, 850-8755099 and Pat Nr. 5.701.636, 56-223PB. Known to work on: Semco Doors, Hoppe Hardware, Hoppe Columbus, Windsor Guide Hinge and Superior Doors

    Hoppe S4002 Hoppe 2-D Horizontal Adjustable Door Hinge - DISCONTIUNED See Product Description for Replacement Option

    1 review

    Out of stock

    Part Number: S4002 - Discontinued - Direct replacement is S4004 style Click here to order and read more information and watch video below.  Columbus 2-D Adjustable Guide Horizontal Door Hinge for Wood and Vinyl Products - Screws not included  Hoppe 2-D Adjustable Door Hinge for Wood and Vinyl Products - Guide Hinge Horizontal Adjustment (+/- 2 mm)  (for vertical adjustment hinge see S4003 replacement style hinge)  Set and Guide Hinge Placement - Also See Hinge Placement Guide Drawing: 3 Hinges Per Door Panel: Starting at top of door Top of door Guide (Part # S4004) Set (Part # S4003) Guide (Part # S4004) 4 Hinges Per Door Panel: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide (Part # S4004) Guide (Part # S4004)  Set (Part # S4003) Guide (Part # S4004) The Set hinge no matter what is always the 2nd from the bottom  Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust do not use power tools but only manual screw driver so you don't strip out the screws.  Manufacture Information and Product Detail:  Settling of walls and floors can make door panels hard to open and close. The 2-D Adjustable Hinge allows easy adjustment of the door both horizontally (+/- 2 mm Guide Hinge Part # S4004) and vertically (+/- 3 mm Set Hinge Part # S4003) with just the turn of a screw. Each hinge is reversible and has maintenance free bearings.  There are two types of adjustable hinges for each door panel A. Set hinge Part # S4003: One per panel. This has vertical adjustment  (+/- 3 mm). B, Guide Hinge Part # S4004: Minimum of two per panel. These hinges only have the horizontal adjustment (+/- 2 mm) Normal hinge replacement has the set hinge. Using a Phillips screwdriver, first adjust the panel up or down by turning the screw marked "V" on the set hinge. When turning the screw in the direction of the arrow (counter clockwise) the other leaf will be pushed in the direction of the arrow. Automatic screwdrivers are NOT recommended. Known Part Numbers: 122340200, 850-8755099 and Pat Nr. 5.701.636 Known to work on: Semco Doors, Hoppe Hardware, Hoppe Columbus, Windsor Doors and Superior Doors, Loewen Doors and many more door brands. *Finish Note: Not for Coastal or High Humidity Applications. These hinges do not come in a sea coast or stainless material, high humidity or costal application can cause hinges to corrode this is not a product defect.

    Out of stock

    $ 0.00

  • S4011 Hoppe Adjustable Hinge  - Set Hinge Known Part Numbers: 850-2972364, 850-2972410, 850-2972372, 850-3113431, 850-2972399, 850-2972401, 850-2972655, 850-2972743, 850-2972680, 850-311-3529, 850-2972701, 850-2972719,850-3033924, 850-3052201, 850-3033941, 850-3033967, 850-3033916, 850-3052156, 850-3033932, 850-3033959

    Hoppe S4011 Hoppe Adjustable Door Hinge - Set Hinge- Non Removable Pin

    13 in stock

    Part Number: S4011 - SET Hinge Hoppe Adjustable Door Hinge Non Removable Hinge - Set Hinge Vertical Adjustment  S4011 is Vertical Adjustment ONLY Watch video and read instructions in pictures (For Horizontal adjustment see part number S4012 Sold Separately and see hinge placement guide in picture) No Screws Included, sold individually  Handing: Left Hand Hinge Used For: Left Hand In swinging (LHI) or Right Hand Out Swinging (RHO) Right Hand Hinge Used For: Right Hand In Swinging (RHI) Left Hand Out Swinging (LHO) SEE  Hoppe "Application Diagram for Set Hinge” TO DETERMINE WHAT HANDING HINGE TO ORDER Pre-Order are Special order items, no returns  Made out of Brass or Aluminum. Multiple finishes to choose from.  Designed for a Greater Advantage • Adjusts vertically ( Use Set Hinge Part # S4011) and  for horizontally ( see Guide Hinge Part # S4012) by 1/8" for a perfect swing. - see Installation Instructions page 1 number of hinges chart for application. • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish.  Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012)  Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012)   Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012) Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012)  The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known to have been used on: Sierra Pacific Doors, Ashworth and many other

    13 in stock

    $ 55.00 - $ 130.00

  • S4014 Hoppe Millennium Adjustable Hinge - 2-D Guide Hinge with Non-removable Pin For Peachtree and WeatherSheild patio Doors. Part Number: S4014, 850-8754743, 122190600, Pat.Nr. 5.701.636 122190600, 850-8754743

    Hoppe S4014 Hoppe Millennium Adjustable Hinge - 2-D Guide Hinge

    17 in stock

    Part Number: S4014 S4014 Hoppe Millennium Adjustable Hinge - 2-D Guide Hinge with Non-removable Pin Horizontal Adjustment  - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors Colors Still Available: Stainless Steel  Discontinued Colors: Oil Rubbed Bronze, Antique Brass, Brass, Brushed Chrome Pat.Nr. 5.701.636 122190600, 850-8754743 Set and Guide Hinge Placement: 3 Hinges Per Door Panel - Up to 165 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel -Up to 165 lbs: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel - 165 - 330 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 5 Hinges Per Door Panel - 165 to 330 lbs: Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known part # 850-8754731, 850-8754743,122190600  General HOPPE Adjustable Hinge Adjustment Instructions: Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above. Prepare the door panel and frame. Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed. On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening. Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges. Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout. Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge. Disassembly Do not attempt to remove the hinge pin, as this may cause damage. To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges. Carefully remove either the frame leaf screws or door leaf screws to displace the panel. Adjustment Instructions Introduction There are two types of HOPPE Adjustable Hinges on each door panel: Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment. Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge. Hinge designs may vary, but adjustment remains the same. Required Tools A 3/16” hex wrench is required. A small flat head screwdriver is required. A plastic putty knife is recommended. Vertical Adjustment for Doors with One Set Hinge With the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel. Reinstall the Finial Cap removed in Step 1. Vertical Adjustment for Doors with Two Set Hinges With the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. To raise the panel, insert the hex wrench into the top-most Set Hinge and tighten the adjustment screw to achieve the desired Insert the hex wrench into the other Set Hinge and tighten the adjustment screw 1/8 turn past the onset of resistance to distribute the panel weight evenly between both Set Hinges. To lower the panel, insert the hex wrench into the top-most Set Hinge and loosen the adjustment screw as far as possible without Insert the hex wrench into the other Set Hinge and loosen the adjustment screw to achieve the desired adjustment. Retighten the adjustment screw on the top-most 1/8 turn past the onset of resistance to distribute the panel weight evenly between both Set Hinges. Reinstall the Finial Caps removed in Step 1. Horizontal Adjustment With the door open: Insert a 3/16” hex wrench into the horizontal adjustment screw. Turn clockwise to decrease the margin and counterclockwise to increase the margin on the hinge side.

    17 in stock

    $ 120.00

  • 850-2664581

    Hoppe S4012 Hoppe Adjustable Hinge - Guide Hinge - Non Removeable Pin Style

    12 in stock

    Part Number:  S4012 – Guide Hinge Hoppe Adjustable Hinge - Guide Hinge - Non Removable Pin Style. S4012 is Horizontal Adjustment Only (Watch video and read instructions in picture's) No Screws Included, sold individually  GUIDE HINGES ARE NOT HANDED. Will work on both LH and RH Doors by how you mount the hinge If not in stock - Pre Order - Special order item - no return 3-8 week lead time  Made out of Brass or Aluminum. Multiple finishes to choose from.  Designed for a Greater Advantage • To Adjust vertically (Use Set Hinge Part # S4011) and  for horizontally (Use Guide Hinge Part # S4012) by 1/8" for a perfect swing. See Installation Set and Guide Hinge Placement • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish. Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012)  Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012)   Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012)  Guide (Use Part # S4012) Set (Use Part# S4011)  Set (Use Part# S4011) Guide (Use Part # S4012)  The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known to have been used on Sierra Pacific Doors and Ashworth

    12 in stock

    $ 55.00 - $ 130.00

  • S4013 Hoppe Millennium Adjustable Hinge - 2-D Set Hinge - Peachtree Weathershield Door Hinge Pat.Nr. 5.701.1636, 122210600, 850-8758419

    Hoppe S4013 Hoppe Millennium Adjustable Hinge - 2-D Set Hinge

    41 in stock

     Part Number: S4013   Hoppe Millennium Adjustable Hinge - 2-D Set Hinge with Non-removable Pin Vertical Adjustment  - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors Colors Still Available: Stainless Steel Discontinued Colors: Oil Rubbed Bronze, Brass Chrome, antique brass Pat.Nr. 5.701.1636, 122210600   Set and Guide Hinge Placement Table: 3 Hinges Per Door Panel - Up to 165 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel -Up to 165 lbs: Anytime you need 4 hinges you would just add another guide hinge Starting at top of door Top of door Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Guide - Part Number S4014 4 Hinges Per Door Panel - 165 - 330 lbs: Starting at top of door Top of door Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 5 Hinges Per Door Panel - 165 to 330 lbs: Guide - Part Number S4014 Guide - Part Number S4014 Set - See Part Number S4013 Set - See Part Number S4013 Guide - Part Number S4014 Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.  Known part # 850-2388803, 850-8754819, 122210600   General HOPPE Adjustable Hinge Adjustment Instructions: Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above. Prepare the door panel and frame. Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed. On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening. Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges. Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout. Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge. Disassembly Do not attempt to remove the hinge pin, as this may cause damage. To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges. Carefully remove either the frame leaf screws or door leaf screws to displace the panel. Adjustment InstructionsIntroductionThere are two types of HOPPE Adjustable Hinges on each door panel: Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment. Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge. Hinge designs may vary, but adjustment remains the same. Required Tools A 3/16” hex wrench is required. A small flat head screwdriver is required. A plastic putty knife is recommended. Vertical Adjustment for Doors with One Set HingeWith the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap. Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel. Reinstall the Finial Cap removed in Step 1. Vertical Adjustment for Doors with Two Set HingesWith the door closed or open: Remove the press-fit Finial Cap from the bottom of the Set Hingeto expose the adjustment screw. Use the small screwdriver forSet Hinges featuring a plastic Finial Cap. A plastic putty knife isrecommended for Set Hinges featuring a brass Finial Cap. To raise the panel, insert the hex wrench into the top-most SetHinge and tighten the adjustment screw to achieve the desiredInsert the hex wrench into the other Set Hinge andtighten the adjustment screw 1/8 turn past the onset of resistanceto distribute the panel weight evenly between both Set Hinges. To lower the panel, insert the hex wrench into the top-most SetHinge and loosen the adjustment screw as far as possible withoutInsert the hex wrench into the other Set Hinge andloosen the adjustment screw to achieve the desired adjustment.Retighten the adjustment screw on the top-most 1/8 turn past theonset of resistance to distribute the panel weight evenly betweenboth Set Hinges. Reinstall the Finial Caps removed in Step 1. Horizontal AdjustmentWith the door open: Insert a 3/16” hex wrench into the horizontal adjustment screw. Turn clockwise to decrease the margin and counterclockwise toincrease the margin on the hinge side. IF THIS HINGE DOES NOT LOOK EXACTLY LIKE YOUR ADJUSTABLE HINGE. CLICK HERE TO SEE ALL THE ADJUSTABLE HINGES WE HAVE ON OUR WEBSITE TO ORDER. IF YOU ARE NOT FINDING YOUR HINGE PLEASE EMAIL OR TEXT OUR RESEARCH DEPARTMENT AND WE WOULD BE HAPPY TO ASSIST YOU

    41 in stock

    $ 120.00

  • Hoppe Multipoint Sliding Door Handle M151Vk/2165N

    Hoppe Hoppe Multipoint Sliding Door Handle M151VK/2165N Product Information Page

    Out of stock

    Hoppe Multipoint Sliding Door Handles M151VK/2165N - Product Information page Product Information page. We do not stock this at our warehouse.  - Use links below to see pricing and to order - Available to Order via our parts catalog website  Handle Set Only See Associated parts sold Separately below  Style: Active With Keyed Cylinder (comes in an exterior keyed lock cylinder and 2 keys) Resista Brass F77-R - Model 850-2081959 Antique Brass F73* - Model 850-2081967 Brushed Chrome F41-R - Model 850-2081975 Polished Chrome F41-R  - Model 850-2081983 Pure White F9010 - Model - 850-2081991 Matte Black F9714 - Model 850-2082003 Satin Nickel F42-R - Model 850-2082011 Antique Nickel F44-R* - Model 850-2082020 Oil Rubbed Bronze F79* - Model 850-2082038 Rustic Umber F8709 - Model 850-2083743 Active without Keyed Cylinder (will not be able to lock or unlock the door from the exterior)  Dummy (no locking capability used on secondary door panel)  Product Info: Manual lock operation eliminates inadvertent locking of the door Faceplate with radius at top and bottom available for simplified door edge preparation 90º turn lock for easy operation and a clear, visual indicator of locked/unlocked position HLS 9000 Associated Parts Sold Separately  Hoppe Sliding Door Multi Point Gear 16mm Faceplate 30 mm Backset gear Hoppe Sliding Door Multi Point Gear 16mm Faceplate 35 mm Backset gear Hoppe Sliding Door Multi Point Gear 20mm Faceplate 30 mm Backset gear Hoppe Sliding Door Multi Point Gear 20mm Faceplate 35 mm Backset gear Hoppe Sliding Door Multi Point Strike 16mm  Hoppe Sliding Door Multi Point Strike 16mm with Bump Out  Hoppe Sliding Door Multi Point Strike 20mm  with Bump Out Hoppe Sliding Door Multi Point U Rail Strike 20mm  *Finish Properties

    Out of stock

    $ 0.00

Hoppe

Login

Forgot your password?

Don't have an account yet?
Create account