Part Number S4102
Hoppe 90 Degree Profile Full Cylinder with Crescent Knob For 1 3/4 Inch to 2 1/2 Inch Thick Door Panel
Can be converted from 90 degree to 360 degree - see pictures for instructions and videos below.
Cylinder Sizing: Verify Door Thickness and Cylinder size by using chart "Inside Distance A" and "Outside Distance B" according to door thickness, Euro groove location and the style of back plate used.
Sizing:
For Doors: 1 3/4 Inch to 2 1/2 Inch Thick Door Panel See chart
For Doors: 2 1/8 inch to 3 inch Doors - see chart Related Parts Sold Separately:
Part Number S4103 - Hoppe Short Cylinder Insert
Part Number S4105 - 2mm or 5/64" Hex Wrench
Part Number S4107 - Set Screw
For 2 1/8 inch to 3 Inch Thick door panel Full Cylinder see part number
Trouble shooting:
If you cannot get the cylinder to line up and go in you need to lower the pin beneath the thumb turn. That frees the cylinder to move and line up for install. Then once put in and turned the cylinder will operate. It is a newer safety feature on these cylinders. Please watch video below.
As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available
805-012- Face Plate - Hoppe Door Handle Set - Hurd Swinging Door
Bright Brass NO SCREWS Included
Discontinued Product. What we have in stock is all that is available. No returns all sales final.
Part Number S4105
For Hoppe and CES
2mm Hex Wrench Cylinder with Crescent Knob
To convert cylinder from 90 degree to 360 degree - see pictures for instructions and videos below.
Special order item no returns. Please expect a lead time of 1-4 weeks.
Related Parts Sold Separately:
Part Number S4102 - Hoppe Full Cylinder
Part Number S4103 - Hoppe Short Cylinder Insert
part Number S4105 - Hex Wrench
Part Number S4107 - Set Screw
As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available
805-013- Face Plate - Hoppe Door Handle Set - Hurd Swinging Door
Bright Brass NO SCREWS Included
Discontinued Product. What we have in stock is all that is available. No returns all sales final.
Once stock is gone to order new handle set see part number S4100AC
As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available
805-006 - Exterior Face Plate - Hoppe Door Handle Set - Hurd Swinging Door
3 exposed screw holes (no screws included)
Discontinued Product Part- what we have in stock is all that is available. Sold as is, all sales final.
M216N stamped on back of face plate
No Longer available to order new handle set see part number S4100AC
As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available
805-005 - Thumb Turn Only - for Hoppe Door Handle Set - Hurd Swinging Door
Part Number: S4013
Hoppe Millennium Adjustable Hinge - 2-D Set Hinge with Non-removable Pin Vertical Adjustment - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors
Colors Still Available: Stainless Steel
Discontinued Colors: Oil Rubbed Bronze, Brass Chrome, antique brass
Pat.Nr. 5.701.1636, 122210600
Set and Guide Hinge Placement Table:
3 Hinges Per Door Panel - Up to 165 lbs:
Starting at top of door Top of door
Guide - Part Number S4014
Set - See Part Number S4013
Guide - Part Number S4014
4 Hinges Per Door Panel -Up to 165 lbs:
Anytime you need 4 hinges you would just add another guide hinge
Starting at top of door Top of door
Guide - Part Number S4014
Guide - Part Number S4014
Set - See Part Number S4013
Guide - Part Number S4014
4 Hinges Per Door Panel - 165 - 330 lbs:
Starting at top of door Top of door
Guide - Part Number S4014
Set - See Part Number S4013
Set - See Part Number S4013
Guide - Part Number S4014
5 Hinges Per Door Panel - 165 to 330 lbs:
Guide - Part Number S4014
Guide - Part Number S4014
Set - See Part Number S4013
Set - See Part Number S4013
Guide - Part Number S4014
Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.
Known part # 850-2388803, 850-8754819, 122210600
General HOPPE Adjustable Hinge Adjustment Instructions:
Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above.
Prepare the door panel and frame.
Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed.
On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening.
Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges.
Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout.
Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge.
Disassembly
Do not attempt to remove the hinge pin, as this may cause damage.
To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges.
Carefully remove either the frame leaf screws or door leaf screws to displace the panel.
Adjustment InstructionsIntroductionThere are two types of HOPPE Adjustable Hinges on each door panel:
Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment.
Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge.
Hinge designs may vary, but adjustment remains the same.
Required Tools
A 3/16” hex wrench is required.
A small flat head screwdriver is required.
A plastic putty knife is recommended.
Vertical Adjustment for Doors with One Set HingeWith the door closed or open:
Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap.
Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel.
Reinstall the Finial Cap removed in Step 1.
Vertical Adjustment for Doors with Two Set HingesWith the door closed or open:
Remove the press-fit Finial Cap from the bottom of the Set Hingeto expose the adjustment screw. Use the small screwdriver forSet Hinges featuring a plastic Finial Cap. A plastic putty knife isrecommended for Set Hinges featuring a brass Finial Cap.
To raise the panel, insert the hex wrench into the top-most SetHinge and tighten the adjustment screw to achieve the desiredInsert the hex wrench into the other Set Hinge andtighten the adjustment screw 1/8 turn past the onset of resistanceto distribute the panel weight evenly between both Set Hinges.
To lower the panel, insert the hex wrench into the top-most SetHinge and loosen the adjustment screw as far as possible withoutInsert the hex wrench into the other Set Hinge andloosen the adjustment screw to achieve the desired adjustment.Retighten the adjustment screw on the top-most 1/8 turn past theonset of resistance to distribute the panel weight evenly betweenboth Set Hinges.
Reinstall the Finial Caps removed in Step 1.
Horizontal AdjustmentWith the door open:
Insert a 3/16” hex wrench into the horizontal adjustment screw.
Turn clockwise to decrease the margin and counterclockwise toincrease the margin on the hinge side.
IF THIS HINGE DOES NOT LOOK EXACTLY LIKE YOUR ADJUSTABLE HINGE. CLICK HERE TO SEE ALL THE ADJUSTABLE HINGES WE HAVE ON OUR WEBSITE TO ORDER. IF YOU ARE NOT FINDING YOUR HINGE PLEASE EMAIL OR TEXT OUR RESEARCH DEPARTMENT AND WE WOULD BE HAPPY TO ASSIST YOU
Part Number: 819
Hoppe Multipoint Latch Plate
Curved Lip wi with cylinder hole
non handed
Size: 1 5/16 inch wide x 8 13/16 inch High
Color: Bright Brass, Stainless Steel
Hoppe Multipoint Sliding Door Handles M151VK/2165N - Product Information page
Product Information page. We do not stock this at our warehouse. - Use links below to see pricing and to order - Available to Order via our parts catalog website
Handle Set Only See Associated parts sold Separately below
Style:
Active With Keyed Cylinder (comes in an exterior keyed lock cylinder and 2 keys)
Resista Brass F77-R - Model 850-2081959
Antique Brass F73* - Model 850-2081967
Brushed Chrome F41-R - Model 850-2081975
Polished Chrome F41-R - Model 850-2081983
Pure White F9010 - Model - 850-2081991
Matte Black F9714 - Model 850-2082003
Satin Nickel F42-R - Model 850-2082011
Antique Nickel F44-R* - Model 850-2082020
Oil Rubbed Bronze F79* - Model 850-2082038
Rustic Umber F8709 - Model 850-2083743
Active without Keyed Cylinder (will not be able to lock or unlock the door from the exterior)
Dummy (no locking capability used on secondary door panel)
Product Info:
Manual lock operation eliminates inadvertent locking of the door
Faceplate with radius at top and bottom available for simplified door edge preparation
90º turn lock for easy operation and a clear, visual indicator of locked/unlocked position
HLS 9000
Associated Parts Sold Separately
Hoppe Sliding Door Multi Point Gear 16mm Faceplate 30 mm Backset gear
Hoppe Sliding Door Multi Point Gear 16mm Faceplate 35 mm Backset gear
Hoppe Sliding Door Multi Point Gear 20mm Faceplate 30 mm Backset gear
Hoppe Sliding Door Multi Point Gear 20mm Faceplate 35 mm Backset gear
Hoppe Sliding Door Multi Point Strike 16mm
Hoppe Sliding Door Multi Point Strike 16mm with Bump Out
Hoppe Sliding Door Multi Point Strike 20mm with Bump Out
Hoppe Sliding Door Multi Point U Rail Strike 20mm
*Finish Properties
Part Number S4107
S4107 Hoppe Set Screw For Cylinder with Crescent Knob
Special order item no returns. Please expect a lead time of 1-4 weeks.
Related Parts Sold Separately:
Part Number S4102 - Hoppe Full Cylinder
Part Number S4103 - Hoppe Short Cylinder Insert
Part Number S4104 - Ring Wrench Removal Tool
Part Number S4105 - 2 MM Wrench
Part Number S4106 - Plastic Insert
Part Number S4103
Hoppe 90 Degree Short Cylinder Insert with Crescent Knob For 1 3/4 Inch Doors
Can be converted from 90 degree to 360 degree - see pictures for instructions
Special order item no returns. Please expect a lead time of 1-4 weeks.
Related Parts Sold Separately:
Part Number S4102 - Hoppe Full Cylinder
Part Number S4105 - 2mm or 5/64" Hex Wrench
Part Number S4107 - Set Screw
As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available
805-011- Dummy Handle Set - Hoppe Door Handle Set - Hurd Swinging Door
Bright Brass NO SCREWS Included
Discontinued Product. What we have in stock is all that is available. No returns all sales final.
