Vetter Windows and Doors Replacement Hardware and Parts

Part Number 335 Balance Window Springs For Single and Double Hung windows. Replacement window springs used on many single hung and double hung windows with compression tilt jamb jamb liners. Each spring will come with a Clip as shown in picture. Clip is removable if you do not need it on your window.Due to the multiple sizes springs come in we do not stock springs. All springs are special order with a 2-4 week lead time. NO RETURNS for springs as they are special order/made to your order.Spring is 3/8" Diameter outside to outsideThe spring gauge or tension is as follows and is commonly associated with these color tips on the springs themselves: Red .041, Green .044, Yellow .047, Black .048, Purple .051To Order By Spring Length Inches : Measure from tip of Eyelet to tip of Eyelet on spring. (Eyelet is the round bent out part of the spring located at both ends).To know what color gauge and length to order: you will need to remove the springs from the jamb liner. Most Springs are color coded at one end with paint. Please watch both how to videos below that show how to remove the jamb liners from your window/reinstall and how to remove and replace the springs. You can also use the chart in the pictures as a guide on which gauge to order (chart is for Hurd Wood/clad windows) other brand windows lengths or gauge of the springs can vary. so ordering a longer spring than needed is recommended and you can cut it to the length you need.  You can also determine gauge of a spring using a spring wire gauge, pocket wire gauge, or a math formula: Math formula: Count 20 coils of the spring and measure their length in inches. Then, divide the measurement by 20 to determine the wire size (see video below at bottom of product page) Spring wire gauge: Insert the gauge into the spring and count 20 coils. Then, look at the gauge markings to find the wire size. Pocket wire gauge: Match the coils on the spring to the correct wire size key in the gauge. Pro Tip: If the Springs are old and maybe a little stretched out it is better to order springs longer then you need as you can cut the springs shorter if needed by using a pair of Wire Cutters or Cable Cutters. Then you can bend out the eyelet with pair of regular pliers and flat head screw driver. See demonstration video below.Lead Time: Due to the multiple sizes springs come in we do not stock springs. All springs are special order with a 1 - 2 week lead time. NO RETURNS for springs as they are special order/made to your order. Larger orders may have longer lead times. Please contact us with any questions.   Have been used on Hurd, BiltBest, Weather Sheild and Caradco, Vetter, Pozzi, Shelter, Windsor, Rivco windows and many other window brands.

Read more less

Part Number 152 EntryGard (EntryGuard) Dual Arm Operator 5 17/64" (inch) Style Handing:  Left Hand Right Hand View pictures and how to video below (2:40 min) to determine handing you need. Measurements in Chart (Scroll Thru Pictures for Chart):  "A" Measurement in Drawing is 5 17/64" Circled in red in chart "B" Measurement in Drawing is 4 7/16"  circled in red in chart The other arm sizes are available for "A" and "B" measurements which can be ordered using our links below using our factory drop ship part catalog website (scroll thru pictures to see arm option chart for part numbers and See how to video below on how to read the chart).  Styles Available : Link Offset Up  Link Offset Down   Note: Detached clips can be revered in the field to be on top of bottom of arm. 152 will all come as Clip on the top. Finish:  E-Gard Handle and Cover Sold Separately See part # 139 for handle and #166 cover, S1002 Cover or upgrade to #S1004 for nesting handle and cover.  Known Part Numbers: 20910, L30941, 40853, U.S. PAT. 4,241,541 - CAN. PAT. 350,432 - PAT. 1982 , 31538, 40754, 45179, 40753, 31538A, 20810A, 15-63-00-002 15-63-00-001, MONCSE953, R3-2256, 53-2255  Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Norco Milgard, Sierra Pacific, Allsco (1980 to Dec. 1997), Monarch Old Series and more. Other Arm Sizes Links to Order (this is an update to our video below). Watch video to see how to read chart in pictures above to determine your A and B Measurements match part numbers on chart to links below: Click here to order: 36-181 Click here to order: 36-182 Click here to order: 36-183 Click here to order: 36-184 Click here to order: 36-186 Click here to order 36-185 Info on our parts catalog factory direct website Cut Sheet For EntryGard Dual Arm 15 Series 

Read more less

Part Number: 139 3 1/2 inch with 11/32 Inch Spline Replacement 3" Window Roto Operator Crank Handle for Amesbury Truth with 11/32" Spline Operators Truth Handle - Roto - Replacement Parts for Awning and Casement Windows operators.Colors: Bronze, New Goldtone, White, Beige, Brass, Goldtone, Clay, Aluminum, Chestnut Bronze, Medium Bronze, Brushed copper Nickel, Off-White, Black, Cocoa Brown, Blue White (aka Bright White), Tuscan Bronze, Oil Rubbed Bronze, Off White (aka Euro white) Special Order Colors:  Special order colors or Pre-order colors are non returnable and can have up to a minimum 3 week lead time. Large QTY orders of 10 or more will also be considered special order none returnable. ** Please note: That the Short Handle Roto Crank has been discontinued by the manufacturer. Once our stock is depleted we will ship out the longer version of the Roto Crank Handle that will work on your windows. Known to have been used on many window Brands: Biltbest, Crestline, Caradco, Peachtree, Vetter, Oldach, Windsor, Sliver Line, weather shield,  and Crank Handle standard Hurd used on  casement and awnings  manufactured pre February 1998 and more window brands that used truth hardware   Known Part Numbers: 139, 45054 31, HCSE29 known part numbers stamped on the back of the older style version of this handle: PAT 4.083.264   and    PAT 4.189.248, 45199, 30905 (older version no longer manufactured the 139 is the closest replacement option available)   

Read more less

Part Number 166 EntryGard Replacement Covers Only - 10341 Amesburty Truth  Truth EntryGard Operator Contour Cover Only - Fits 15 Series EntryGard Casement and Awning Operator andHandles 139 and 135 sold separately  - See Accessories items Known Part Numbers On Operator: 20910, L30941, 40853, U.S. PAT. 4,241,541 - CAN. PAT. 350,432 - PAT. 1982 , 31538, 40754, 45179 Discontinued Color:  Coppertone. For Additional Entrygard Covers in different styles  and colors see part numbers S1002 and S1004  Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Milgard, Sierra Pacific and more. Free Economy Shipping On All USA Orders. If Cover color or QTY you want to order is is out of stock you can pre-order and parts will ship out as soon as they come in from the factory.

Read more less

Part Number: 131   Folding Crank Handle for Amesbury Truth 11/32 Spline OperatorsColors: Aluminum, Beige, Black, Bright White, Bronze, Chestnut Bronze, Clay, Faux Oil Rubbed Bronze, New Goldtone, Tuscan Bronze White  Special order Colors: Goldtone, Oil Rubbed Bronze, Bright Brass are a non returnable item- no returns for these items Large Quantities Order: orders with QTY 50 or more are special order items no returns or order cancellations.  Related Parts: Part # 101 Truth Maxim Dual Arm Casement Operator Part # 102 Truth Maxim Split  Arm Dyad Casement Operator Part # 209 Truth Maxim Awning Operator  Part # 111 Truth Ellipse Style Split Arm Dyad Casement Operator  Part # 105 Truth Ellipse Style Straight Arm Casement Operator  Other Amesbury Truth Operators  Part # 131 Folding Handle was primarily used on Part # 101, 102 and 209 Truth Maxim casement and awning operators). Replacement part for Hurd Casement and awing window operators Vintage Classic Style: 02/02/1998 - 9/17/2007. Also used on many other window brands that use Truth Hardware  Known Part Numbers: Truth, 45393, U.S. PAT. 351490, 5560082, 131, Truth 3, 037189, 037188, 091691, 11329-32, HCSE31, A3-2104, A4-2149, A4-2150, A4-2147, A4-2148, 00-0000  Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Milgard, Sierra Pacific, Vetter, Allsco and more. Updated 7/24/23

Read more less

Part Number: S1107 Amesbury Truth 16 Series HomeGard Casement Window Sash Lock Color: White and Bronze  (New Goldtone has been discontinued and once our stock is gone it will no longer be available) What's Included: Each lock is Sold complete with: 1 Lock, 1 Left Keeper, 1 Right keeper and color matching mounting screws for lock and keeper (so you can use on either left hand or right hand operating casement windows). Dimensions: 2 1/4 Inch Wide x 2 3/4" Tall x  3/8 Inch deep at 1st step and 15/16 inch deep at 2nd step Screw Hole Spacing: 2 5/16 Inch Center to Center  HomeGard Sash Locks are a perfect low-profile lock option for windows with smaller side stops. Featuring .625" pull-in, HomeGard locks offer a strong detent which consistently provides a more secure feel during lock up. HomeGard locks can withstand negative air pressure of 275 lbs. per lock. Known to have been used on: Crestline, Vetter and Peachtree Windows, Semco  Known part number stamped on back: 45428 Truth, Truth w/ House Symbol Replacement version for locks stamped with 21328A, Retro fit replacement option for lock with stamp on back of 31664  

Read more less

Part Number: 901 Amesbury Truth Kerf Mounted Hollow Window Weather Strip / Gasket Special Features: TPE bulb Weather Seal. Designed for 0.078" kerf. Other Information: Hollow TPE Bulb Seals Color: Gray Sold by the foot Rolled: Quantity 1 = 1 foot. Larger QTY's maybe shipped in multiple rolls. Example if you order 300 feet you may receive QTY 6 - 50 foot rolls. Some rolls maybe in increments of 25 feet. (full spool comes in 1000 feet only)  no returns of rolls of less than 25 feet Returns will only be accepted for full uncut rolls in increments of 25, 50 and 100 feet. No returns on 1000 foot spools Known Part Number: 1727, 015512, HCSE454 Known Brands: Hurd Windows, AmesburyTruth, and many other window brands. Maintenance: Weather Strip Seals are an maintenance item. You should replace your weather strip periodically once it’s worn out so windows seal properly. Lifespan of weatherstripping depends on your climate, weather conditions of the area you live in, and other wear and tear factors that is put on the window.

Read more less

Part Number: 216 Crank Handle Adapter 5/8 Inch Hex Femail used with Clear Story Windows Size: Spline Size see list below (see pictures spline size guide and video on how to verify measurements with calipers)  11/32 Spline Fits: Truth (Amesbury Truth): Marvin, Some Milgard, Caradco, Weather Shield, Hurd, BiltBest, Eagle, Vetter, Roto X Drive, Anderson 100 series and Others 9/32 & 5/16 Spline Fits Peachtree, Getty, Door Chester, old style steel casements, Jalousie  3/8 Special Spline Fits: Pella 3/8 Spline Fits: Anderson (but not Anderson 100 series use Truth 11/32” spline)  5/16 HEX Spline Fits: Some Milgard and Others (5/16 Hexagon 6 sided spline)  Finish: Mill (Special order colors email for pricing: White, Black and Champagne)  Put those operable clerestory windows to energy-saving use with our 39-series clerestory extension crank. High mounted windows are excellent for capturing light while providing privacy, but they can also be “excellent” heat traps. It is now possible to vent the heat that rises to these areas as easily as opening any other window in the home.It’s inexpensive and can easily retrofit to existing or new window installations. By simple removal of the existing crank handle and replacement with an adapter (Hex-Bolt) the crank will open and close any operable clerestory window. It is not necessary to replace the current operator.The removable extension crank is available in many standard sizes for either sill or jamb mounted operators. (See Manual Window Wands) The standard finish for the crank is natural anodized aluminum.

Read more less

Part Number: 135 Amesbury Truth T Crank Handle. Also called Wing handle or Butterfly Handle Crank Handle for Amesbury Truth 11/32 Spline OperatorsUsed primarily on: the Amesbury Truth DLX Maxim, 15 series, 11 series casement and awning window Operators.Colors In Stock: Goldtone, Bronze, White, Clay, Aluminum, Black, New Goldtone,   Special Order Colors: Chestnut Bronze, Brushed Copper Nickel, Off-White, Cocoa Brown, Bright White, (No returns 1 - 3 week lead time).  Special Order Colors: Email info@WindowPartsCenter.com for pricing quote. minimum order maybe required Oil Rubbed Bronze (this is a faux ORB),   Known Part Numbers: 136, Truth 40984, 021951, 37-125-2 Used on: Amsbruty Truth Operators, Norco, Hurd Casement and Awnings, Weather Shield, and more.  Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Milgard, Sierra Pacific, Vetter and more. Replacement part for Hurd Casement and awing window operators Vintage Classic Style: 02/02/1998 - 9/17/2007 and many other window brands that use Truth Hardware  

Read more less

Part # 177 Replacement Amesbury Truth Non Folding Contour Handle - 11/32" Spline For Casement and Awning Window Operators.  Colors in stock: White, Bronze, Goldtone, New Goldtone and Beige Special Order Colors: Bright Brass, Clay, Aluminum, Chestnut Bronze, Brushed Copper Nickel, Black, Coppertone, Cocoa Brown, Bright White, Tuscan Bronze, Oil Rubbed Bronze. Special order colors are non returnable and can have a 1-3 week lead time. Replacement part for Hurd Casement and awing window operators Vintage Classic Style: 02/02/1998 - 9/17/2007 and many other window brands using Truth Operators, Allsco, Norco, Vetter, Windsor, Pozzi and many more window brands. Known Part Numbers: Truth 45240, 177, 010768, 010769, 090934, 11454-32, HSCE30, G4-2051, G4-2050, G4-2049, A3-2106, G5-2048, G5-2047, G5-2045, G5-2046

Read more less

Part Number 211 Truth 11 Series (11.12) Awning Short Arm Operator Single Pull - 16 1/4 Wide Colors In Stock: White, Bronze and New Goldtone  Special Order Color: Clay, Beige and Goldtone are special order item. 1-4 week lead time No Returns Known to be used on Hurd Brand Windows with glass widths: 19 & 23, this part has been used on many other window brands such as Weather Sheild, Caradco, Biltbest and more. Associated Parts Sold Separately:  Part Number 139 Crank Handle  Part Number 135 T Handle  Part Number 108 Knob Handle Part Number 218 Center Hook  Below video shows how to replace an awning operator. Steps are very similar when you are replacing part number 211.  Known Part Numbers: 211, U.S. PAT. 4505601, PAT. CAN. 1986, 4530, 30896, 11-12-32-001        

Read more less

Part Number 215   Manual Window Wand For Clear Story Windows Special Order Item - NO RETURNS or Order Cancellations  - due to material shortages lead times are longer then normal expect a minimum of 12 weeks for your order to ship. We will update with better lead times as soon as the factory lets us know.  Put those operable clearstory windows to energy-saving use with our clerestory extension crank. High mounted windows are excellent for capturing light while providing privacy, but they can also be “excellent” heat traps. It is now possible to vent the heat that rises to these areas as easily as opening any other window in the home.It’s inexpensive and can easily retrofit to existing or new window installations. By simple removal of the existing crank handle and replacement with an adapter (see Hex-Bolt part number 216 and 217 sold separately) the crank will open and close any operable clerestory window. It is not necessary to replace the current operator. Remember that you will only need one clerestory crank to operate all windows at the same height. Color: natural anodized aluminum  Size:  is the length of the Wand or Crank Length. (see Chart below) Styles available: Sill Mounted or Jamb Mounted (see picture or video)  You must buy corresponding adapter to use wand (sold separately) . See part # 216 or # 217  Don't know what size to order?  Distance from floor is the measurement from the floor to the window. Example if the distance from the floor to the window is 7' then its advised to get a 3' wand or Crank length. See Chart Below for factory recommendations on length. Chart: Distance From floor 7 foot = Factory Recommends 3 foot Crank LengthDistance From floor 8 foot = Factory Recommends 4 foot Crank LengthDistance From floor 9 foot = Factory Recommends 5 foot Crank LengthDistance From floor 10 foot = Factory Recommends 6 foot Crank LengthDistance From floor 11 foot = Factory Recommends 7 foot Crank LengthDistance From floor 12 foot = Factory Recommends 8 foot Crank LengthDistance From floor 13 foot = Factory Recommends 9 foot Crank Length (KD)*Distance From floor 14 foot = Factory Recommends 10 foot Crank Length (KD)*Distance From floor 16 foot = Factory Recommends 12 foot Crank Length (KD)* *KD = Knocked Down (wand shipped in 2 pieces and you have to screw them together) see assembly instructions in pictures. Parts sold separately: Part Number 216 - Crank Handle Adapter for ClereStory Windows "Female" Part Number 217 Clear Story Manual Window Wand Crank Adapter "Male"

Read more less