Hoppe

Part Number 810   Flipper/Tongue Style Hoppe Multi point for Hurd Swinging Patio Doors and others (If your door is another door brand please email us and we can email you a worksheet you ok will need to fill out to get you the correct Hoppe multipoint for your door. info@windowpartscenter.com) Brass color no longer manufactured - only comes in stainless steel for both the gear box and the extensions.  Comes with: bottom extension with gear box attached and the top extension (choose your door height size). The Hoppe #810 Roller style is the direct replacement for old FUHR Roller Multi point that was on Hurd doors – no modification is needed when changing to the Hoppe #810. The only difference is some of the FUHR multi point had an automatic fire to engage the multi point, the Hoppe does not. So with the Hoppe to engage the multi point you close the door then lift up on the door handle then throw the dead bolt to lock. Hoppe Roller Style will also replace the Old FUHR Roller style. handing: Non handed latch is reversible. See video on how to change latch handing   Top Extension: Comes in Door Heights: Retro/6-8, 6-10, 7-2, 8-0. Style Options: Hoppe Gear Box Pin/Roller Style Hoppe Gear Box Flipper/Tongue Style Hurd Door Panel Heights for Top Extension:77" = Retro/6-878" = Retro/6-880" = 6-1084" = 7-293" = 8-0For Classic Hurd Doors Manufactured from 2005 and PriorFuhr Multi point used on Classic Hurd doors are no longer manufactured - Hoppe Multi point is the direct replacementNumber Known To Have Been On Older Gear Box (Hoppe Roller Style Brass Color): 1334291 - this is a component number.  Install Instructions (also see instructions in pictures): Remove set screws on handle levers and remove remove three mounting screws on faceplate estuation  On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the multipoint system (keep all screws you will reuse them) Install new multipoint with screws Test for Operation  Reinstall handle set Test for proper operation

Read more less

Part Number: S3004 - Sold Individually  Hoppe Handle Set Screw Size: 6M x 12 mm 304SS 

Read more less

Part Number: 829 Hoppe Split Shaft only screws sold separately (See Part Number: 840-031 Set Screws or S3004 - metric 6-10) Shaft Size Order By Length:  3 15/16 inch ( 5/16 inch x 3 15/16 inch or 8 mm x 100 mm) For Doors Smaller 1 3/4 inch thick Can be used as a replacement split shaft for old GU handle sets 4 21/64 inch (5/16 inch x 4 21/64 inch or 8mm x 110 mm) For Doors Smaller than 1 3/8 inch thick 4 11/16 inch (5/16 inch x 4 11/16 inch or 8 mm x 120 mm) For 1 3/4 Thick Doors Commonly used on Hurd and Truth hardware 5 1/2 inch (5/16 inch x 5 1/2 inch or 8 mm x 140mm) For 2 1/4" thick doors 6 1/4 inch (5/16 inch x 6 1/4 inch or 8 mm x 160 mm) used with the 1" Hoppe Handle extension part # 828 sold separately Commonly used on Hurd and Truth hardware that has extension 828   See figure F in drawing for correct split shaft spindle position installation.  Associated Parts Sold Separately:  6 1/4 is used with the 1" Hoppe Handle extension part # 828 Part Number: 840-031 Set Screws pack  Part number S3004 - metric 6-10 screws

Read more less

Part Number 810R  Hoppe Multipoint Automatic Roller Bottom Gear Box Extension HLS9000 CUSOTMER PLEASE READ BEFORE YOU ORDER: See chart for dimensions to compare with your multipoint BEFORE you place your order. If measurements do not match for your multipoint please email us for the worksheet you will need to fill out for a quote. Single point gearbox is not interchangeable with multipoint gearbox. The cover may look the same but internal components are different. Info@WindowPartsCenter.com Material: Stainless Steel (sliver). Brass color no longer manufactured - only comes in stainless steel for both the gear box and the extension. See features and benefits picture.  Style: Roller Comes with: bottom extension with gear box attached (top extension SOLD separately see part number 820R for top extension these are for Hurd doors only. For other brand doors please email for worksheet to fill out for a quote)  The Hoppe #810R/820R Roller style is the direct replacement for old FUHR Roller Multi point that was on Hurd – no modification is needed when changing to the Hoppe #810 - you need to order both top extension 820 and lower extension with great box 810 to use as a replacement with old FUHR. The only difference is some of the FUHR multi point had an automatic fire to engage the multi point, the Hoppe does not. So with the Hoppe to engage the multi point you close the door then lift up on the door handle then throw the dead bolt to lock. Handing: Non handed latch is reversible. See video on how to change latch handing  Associated Parts Sold Separately: 820R - Hoppe Multipoint Automatic Roller TOP Extension HLS9000 813 -  Hoppe 3Pt Convert Auto Release Striker  833 -  Hoppe 3Pt Convertible Under plate  834 - Hoppe 3Pt Striker For Rollers 819 - Hoppe Multipoint Latch Plate  S4019 - Hoppe LATCH AND DEADBOLT STRIKE WITH CURVED LIP S1400AC - Active with Cylinder Munchen Series M112PI/216N Handle Set S4300AC - Active with Cylinder Hoppe Munchen Series M112PI/3965N Handle Set S4200AC - Active with Cylinder Hoppe Munchen Series M112PI/374N Handle Set S4100AC - Active with Cylinder Hoppe Munchen Series M112PI/216N Other Hoppe Multipoint and Single Point We Stock: 810T - Hoppe Multipoint Automatic Tongue Lower Extension HLS9000 820T - Hoppe Multipoint Automatic Tongue TOP Extension HLS9000 825 - Hoppe Single point Gear Box For Hoppe Multipoint We Do Not Stock Please Email us for worksheet and quote  Install Instructions (also see instructions in pictures): Remove set screws on handle levers and remove remove three mounting screws on faceplate estuation  On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the multipoint system (keep all screws you will reuse them) Install new multipoint with screws Test for Operation  Reinstall handle set Test for proper operation 810R Known to have been used on: For Classic Hurd Doors Manufactured from 2005 and Prior. Fuhr Multi point used on Classic Hurd doors are no longer manufactured - Hoppe Multi point is the direct replacement. Number Known To Have Been On Older Gear Box (Hoppe Roller Style Brass Color): 1334291 - this is a component number. 

Read more less

Part Number 827 - SOLD Individually  Hoppe Backplate Bushing  -  (handle set or other parts not included) This Hoppe Backplate Bushing is for Hoppe Swinging Patio Doors System ONLY. Color: Clear Gold Opaque  HANDLE BUSHING HFW F12 BACKPLATE MANUFACTURER: A/35/14 914 RL 750 16S 85 Used on Hurd handle set from 2004 and prior - See picture to match your handle set to correct bushing kit for Hurd DoorsThis Hoppe Backplate Bushing is for Swinging Patio Doors System ONLY.  

Read more less

Part Number 820R  Hoppe Multipoint Automatic Roller Top Extension HLS9000 for HURD DOORS ONLY CUSOTMER PLEASE READ BEFORE YOU ORDER: See chart for dimensions to compare with your multipoint BEFORE you place your order. If measurements do not match for your multipoint please email us for the worksheet you will need to fill out for a quote. Single point gearbox is not interchangeable with multipoint gearbox. The cover may look the same but internal components are different.  Material: Stainless Steel (sliver). Brass color no longer manufactured - only comes in stainless steel for both the gear box and the extension. See features and benefits picture.  Style: Roller Top Extension ONLY Size we stock: (see chart for full details and measurements):  6-8 = Top Extension Length 1019mm / 40.11in Retro = Top Extension Length 1031mm / 40.59in 6-10 = Top Extension Length 1078mm / 42.44in 8-0 = Top Extension Length 1407mm / 55.39in Comes with: Top extension ONLY (Bottom Extension with Gearbox SOLD separately see part number 810R for bottom extension with gear box)  The Hoppe #810R/820R Roller style is the direct replacement for old FUHR Roller Multi point that was on Hurd and other door manufactures – no modification is needed when changing to the Hoppe #810 - you need to order both top extension 820 and lower extension with great box 810 to use as a replacement with old FUHR. The only difference is some of the FUHR multi point had an automatic fire to engage the multi point, the Hoppe does not. So with the Hoppe to engage the multi point you close the door then lift up on the door handle then throw the dead bolt to lock. Associated Parts Sold Separately: 810R - Hoppe Multipoint Automatic Roller Lower Gearbox with Extension HLS9000 813 -  Hoppe 3Pt Convert Auto Release Striker  833 -  Hoppe 3Pt Convertible Under plate  834 - Hoppe 3Pt Striker For Rollers 819 - Hoppe Multipoint Latch Plate  S4019 - Hoppe LATCH AND DEADBOLT STRIKE WITH CURVED LIP S1400AC - Active with Cylinder Munchen Series M112PI/216N Handle Set S4300AC - Active with Cylinder Hoppe Munchen Series M112PI/3965N Handle Set S4200AC - Active with Cylinder Hoppe Munchen Series M112PI/374N Handle Set S4100AC - Active with Cylinder Hoppe Munchen Series M112PI/216N Other Hoppe Multipoint and Single Point We Stock: 810T - Hoppe Multipoint Automatic Tongue Lower Extension HLS9000 820T - Hoppe Multipoint Automatic Tongue TOP Extension HLS9000 825 - Hoppe Single point Gear Box For Hoppe Multipoint We Do Not Stock Please Email us for worksheet and quote  Install Instructions (also see instructions in pictures): Remove set screws on handle levers and remove remove three mounting screws on faceplate estuation  On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the multipoint system (keep all screws you will reuse them) Install new multipoint with screws Test for Operation  Reinstall handle set Test for proper operation 810R/820R Known to have been used on: For Classic Hurd Doors Manufactured from 2005 and Prior. Fuhr Multi point used on Classic Hurd doors are no longer manufactured - Hoppe Multi point is the direct replacement. Number Known To Have Been On Older Gear Box (Hoppe Roller Style Brass Color): 1334291 - this is a component number. 

Read more less

As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available 805-013- Face Plate - Hoppe Door Handle Set - Hurd Swinging Door Bright Brass NO SCREWS Included  Discontinued Product. What we have in stock is all that is available. No returns all sales final. 

Read more less

Part number 828 Hoppe Door Handle Extension  Special Order NO Returns - 3-5 week lead time Split shaft sold separately 

Read more less

S4300AC Active - With Cylinder- Hoppe Munchen Series M112Pl/3965N- Swinging Door Handle Sets Active Door Set - With 90 Degree Cylinder All handle sets are for 1 3/4" thick doors.  Multipoint / Single Point Locking Systems sold separately All Hoppe swing door handles are available in Active, Inactive and Dummy Sets. Special order Item - No returns  Bulk Pricing available in QTY 10 or more (can not mix and match colors).  

Read more less

S4200AC Active - With Cylinder- Hoppe Munchen Series M112Pl/374N- Swinging Door Handle Sets Active Door Set - With 90 Degree Cylinder All handle sets are for 1 3/4" thick doors.  All Hoppe swing door handles are available in Active, Inactive and Dummy Sets. Special order Item - No returns Allow 3-5 week lead time once you place your order.  If your lever is drooping- that’s not a lever issue. It means the lever return spring inside the mortise lock  is either broken or stretched, and you will need to replace the multi point inside the door panel.  Products Sold Separately: Multipoint / Single Point Locking Systems Gear Box are sold separately Additional Notes: Hoppe #S4200AC can be used  interchangeably to replace Roto style 56-111BRS which is now obsolete (Roto S 623 B 24 is stamped on the single point gear box). Please verify dimensions with our drawings of the Hoppe handle set  #S4200AC to make sure you have the correct Roto Trim Handle that is interchangeable with our S4200AC.    

Read more less

S4100AC  Active Style - With 90 Degree Cylinder Hoppe Munchen Series M112Pl/216N Swinging Door Handle Sets Active Door Set - With 90 Degree Cylinder All handle sets are for 1 3/4" thick doors.  Multipoint / Single Point Locking Systems sold separately All Hoppe swing door handles are available in Active, Inactive and Dummy Sets. Special Order Item. No returns exchanges or order cancellations once order has been placed. Please allow 3-6 week lead time.known to have been used on: Classic Active Handle Set for Hurd Swinging Door Product Used: 2004 and Prior Associated Parts Sold Separately: Part number 825 - Hoppe Single Point Gear Box - for multiple door brands  Part Number 810 - Hurd Brand Doors ONLY - Hoppe Multi Point part number: 829 - Replacement Shaft And 2 Set Screws for Hoppe Door Handle Set Part number 828- Hoppe Door Handle Extension   

Read more less

Once stock is gone to order new handle set see part number S4100AC As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available 805-009 - Face Plate - Hoppe Door Handle Set - Hurd Swinging Door Bright Brass  Discontinued Product. What we have in stock is all that is available. No returns all sales final. 

Read more less