Part Number: S4013
Hoppe Millennium Adjustable Hinge - 2-D Set Hinge with Non-removable Pin Vertical Adjustment - Hinges are Non Handed. Works for both Left hand and Right hand swinging doors. Known to been used on WeatherSheild and Peachtree Doors
Colors Still Available: Stainless Steel
Discontinued Colors: Oil Rubbed Bronze, Brass Chrome, antique brass
Pat.Nr. 5.701.1636, 122210600
Set and Guide Hinge Placement Table:
3 Hinges Per Door Panel - Up to 165 lbs:
Starting at top of door Top of door
Guide - Part Number S4014
Set - See Part Number S4013
Guide - Part Number S4014
4 Hinges Per Door Panel -Up to 165 lbs:
Anytime you need 4 hinges you would just add another guide hinge
Starting at top of door Top of door
Guide - Part Number S4014
Guide - Part Number S4014
Set - See Part Number S4013
Guide - Part Number S4014
4 Hinges Per Door Panel - 165 - 330 lbs:
Starting at top of door Top of door
Guide - Part Number S4014
Set - See Part Number S4013
Set - See Part Number S4013
Guide - Part Number S4014
5 Hinges Per Door Panel - 165 to 330 lbs:
Guide - Part Number S4014
Guide - Part Number S4014
Set - See Part Number S4013
Set - See Part Number S4013
Guide - Part Number S4014
Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.
Known part # 850-2388803, 850-8754819, 122210600
General HOPPE Adjustable Hinge Adjustment Instructions:
Determine hinge locations on the frame and door panel. Recommended hinge positions are given in the Set and Guide Hinge Placement Table above.
Prepare the door panel and frame.
Fasten hinges into the door panel. #10 ANSI wood screws with a minimum length of 1 1/4” are recommended. The Set Hinge must be installed according to the installation label. The label on the frame leaf will point down to the sill when properly installed.
On the frame, use #10 ANSI wood screws that are 5/8” to 3/4” long in three of the four screw locations. One screw on each hinge should be at least 1 1/2” long to reach the stud. This screw is typically left out and is installed after the door is positioned in the rough opening.
Install the frame leaf of the Set Hinge into the routing on the frame and fasten securely. Do not allow the Set Hinge(s) to support the weight of the panel without installing the Guide Hinges.
Install the frame leaf of the Guide Hinges into the routings on the frame and fasten securely. Leaves on the Guide Hinges will slide freely up and down for alignment with the rout.
Do not adjust hinges prior to the final installation into the rough opening. This will affect the ability of the door installer and end user to utilize the full adjustment range of the HOPPE Adjustable Hinge.
Disassembly
Do not attempt to remove the hinge pin, as this may cause damage.
To disassemble the door panel from the frame, support the weight of the panel to relieve the weight from the hinges.
Carefully remove either the frame leaf screws or door leaf screws to displace the panel.
Adjustment InstructionsIntroductionThere are two types of HOPPE Adjustable Hinges on each door panel:
Set Hinge: One or two per panel. The Set Hinge provides ± 1/8” vertical adjustment.
Guide Hinge: Two or three per panel. The Guide Hinges provide ± 1/8” horizontal adjustment. Look for the visible adjusting screw on the door sash leaf. This identifies the hinge as a Guide Hinge.
Hinge designs may vary, but adjustment remains the same.
Required Tools
A 3/16” hex wrench is required.
A small flat head screwdriver is required.
A plastic putty knife is recommended.
Vertical Adjustment for Doors with One Set HingeWith the door closed or open:
Remove the press-fit Finial Cap from the bottom of the Set Hinge to expose the adjustment screw. Use the small screwdriver for Set Hinges featuring a plastic Finial Cap. A plastic putty knife is recommended for Set Hinges featuring a brass Finial Cap.
Insert the hex wrench into the bottom of the Set Hinge. Tighten the screw to raise the panel and loosen to lower the panel.
Reinstall the Finial Cap removed in Step 1.
Vertical Adjustment for Doors with Two Set HingesWith the door closed or open:
Remove the press-fit Finial Cap from the bottom of the Set Hingeto expose the adjustment screw. Use the small screwdriver forSet Hinges featuring a plastic Finial Cap. A plastic putty knife isrecommended for Set Hinges featuring a brass Finial Cap.
To raise the panel, insert the hex wrench into the top-most SetHinge and tighten the adjustment screw to achieve the desiredInsert the hex wrench into the other Set Hinge andtighten the adjustment screw 1/8 turn past the onset of resistanceto distribute the panel weight evenly between both Set Hinges.
To lower the panel, insert the hex wrench into the top-most SetHinge and loosen the adjustment screw as far as possible withoutInsert the hex wrench into the other Set Hinge andloosen the adjustment screw to achieve the desired adjustment.Retighten the adjustment screw on the top-most 1/8 turn past theonset of resistance to distribute the panel weight evenly betweenboth Set Hinges.
Reinstall the Finial Caps removed in Step 1.
Horizontal AdjustmentWith the door open:
Insert a 3/16” hex wrench into the horizontal adjustment screw.
Turn clockwise to decrease the margin and counterclockwise toincrease the margin on the hinge side.
IF THIS HINGE DOES NOT LOOK EXACTLY LIKE YOUR ADJUSTABLE HINGE. CLICK HERE TO SEE ALL THE ADJUSTABLE HINGES WE HAVE ON OUR WEBSITE TO ORDER. IF YOU ARE NOT FINDING YOUR HINGE PLEASE EMAIL OR TEXT OUR RESEARCH DEPARTMENT AND WE WOULD BE HAPPY TO ASSIST YOU
no longer available- see part number 840 - Current style for replacement handle set
840-023- Amesbury Truth GU parts Kit- Swinging Patio Door Hurd
Comes with all that you see in the picture.
Discontinued Product. If it's in stock we have it. No Returns all sales are final.
Part Number: 856-857-858
GU Active Multi Point - 2006 - Current Product for Hurd and Sierra Pacific WI Product
Review size sheet to know what to order. If measurements do not match your GU hardware then this will not work on you door.
Special Order Item. No returns exchanges or order cancellations once order has been placed. Please allow 2-3 week lead time.
Part Number: D305 - As Is No Returns
150 Degree Rotation (see picture diagram of rotation) if you would like handle set to be modified to 180 degree rotation please email us as it’s a $35 up charge we will need to add to the order please email us at info@windowpartscenter.com or text us at 303-222-4489
What you will receive is shown in pictures. Handle Set Only - Satin Chrome only available QTY 1 once gone it will no longer be available. Stamped on back of face plates PAT. NO. 4,671,089 1200-126 and 1200-125
Discontinued item and no longer available. When what is in stock is gone use below link to D300 for replacement.
1 handle set will install on 1 door panel. If you have 2 door panels (like a French door) you will need to order 2 handle sets.
For direct replacement see: part numbers D300 and choose Style: Active Modify 180 Degree
Repair Parts:
Part Number 701 bushing kit
no other parts are available for this handle set.
Part Number D305 - as is item. No returns as this ks the old discontinued style
W&F Original 1200-125 Trilennium Handle
Handle Set Only (not back sets - latch or dead bolts- or strike plates included).
6 inch center to center bore. And 5 1/4” center to center screw holes
Can be used on doors with double bore and back sets (latch and dead bolt)
Part Number 823
GU 7/8 inch Door Handle Extension 3/4 inch Includes new Split Shaft choose size for your door (handle sets NOT included)
This 3/4 inch extension only works on GU handle sets that have 7/8 inch lever hole see pictures for examples to compare with your handle set. If your faceplate lever hole is smaller these extensions with NOT work. Verify before you place your order
size
1.71 - split shaft is 4 25/32 inch long
(approximately 4 3/4 inch )
2.25 - spit shaft is 5 17/32 inch long
(approximately 5 1/2 inc long
new split shaft is needed to accommodate the additional extension
Available Finish Colors:
Antique Brass
Bright Brass
Brushed Chrome
Oil Rubbed Bronze
White
Lead Time can be up to 6 weeks
Associated Parts Sold Separately:
Part number 840 - GU Active Handle Set For GU Multi Point Hardware
split shafts 829
Extensions 884
As is -may have minor scuffs, etc.- No returns all sales final. Once our stock is gone this item will no longer be available
Part Number: 878
Columbus 3D Adjustable Door Hinge
Discontinued Product. These are Refurbished hinges.
All sales final no returns
Once stock is depleted we will no longer be able to get any more.
IF THIS HINGE DOES NOT LOOK EXACTLY LIKE YOUR ADJUSTABLE HINGE. CLICK HERE TO SEE ALL THE ADJUSTABLE HINGES WE HAVE ON OUR WEBSITE TO ORDER. IF YOU ARE NOT FINDING YOUR HINGE PLEASE EMAIL OR TEXT OUR RESEARCH DEPARTMENT AND WE WOULD BE HAPPY TO ASSIST YOU.
Part Number: S4016 - Truths Sentry Adjustable Hinges - Set Hinges
If not in stock but a pre order item then it’s a Special order Item No Returns
Screws Not Included
Engineered for maximum strength and security, Sentry Hinges exceed ANSI grade 3 requirements fordoors weighing up to 220 lbs. Sentry Hinges exceed ANSI grade 1 impact specifications. Sentry Hinges aremade of extruded brass and extruded aluminum that provides superior strength and corrosion resistance.Sentry Hinges provided with non-removable pins for maximum security.
Robust, Reliable and Attractive
Industry standard 4" x 4" with 5/8" radius corner
Both Guide (Part # S4015) and Set (Part # S4016) Hinges take a 5/32" hex wrench
Guide Hinge (Part # S4015) has a 11/64" adjustment and Set Hinge (Part # S4016) has a 1/4" adjustment
Extruded brass hinges are provided in decorative finishes including PVD
Extruded aluminum hinges are available in powder coated painted finishes
Composite bushings provide noise-free operation
Set and Guide Hinge Placement:
3 Hinges Per Door Panel:
Starting at top of door Top of door
Guide
Set
Guide
4 Hinges Per Door Panel:
Anytime you need 4 hinges you would just add another guide hinge
Starting at top of door Top of door
Guide
Guide
Set
Guide
The Set hinge no matter what is always the 2nd from the bottom
Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust.
As is - New Condition old stock (may have minor scuffs, etc.) - No returns all sales final. Once our stock is gone this item will no longer be available.
840-008 - Amesbury Truth GU Handle - Set Screw and Shaft Type - Swinging Patio Door Hurd.
Replacement handle only. All other replacement parts sold separately.
Discontinued Product. What we have in stock is all that is available. No returns, all sales final. Some may have minor scratches.
Active Modified 180° Option (Add-On)
For handle Sets D300, D301, D302, D303 and D304 Only
This option modifies the lever handle to rotate 180°, which is required for some older multi-point and double bore systems. (See product images for examples of lever rotation.) For handle set part numbers; D300, D301, D302, D303 and D304
How to order:This is an additional add-on and must be selected under “Accessory Items.”
If you order 1 handle set → add Qty 1 of the 180° modification
If you order 3 handle sets → add Qty 3 of the 180° modification
Each handle set that needs this modification requires its own quantity.
Part Number: S4301
Sold Individually
Hinge Cap replacement for HG100 and HG200 Amesbury Truth Dual Adjustable Door Hinge Part Numbers S4005 S4006 S4007 S4008
Color: Black
Sold Individually
Use on part number: S4005 S4006 S4007 S4008
