Swinging Patio Door Parts
S4110 -W&F French Series Handle Set - The Normandy 5 1/2 Inch Center to Center 1200-68 1200-67 series
Part Number: S4110 Once our stock is gone this item will no longer be available. Sold AS IS - All sales are final. French Series Handle Set - The Normandy by W&F 5 /12" Center to Center Bore, 3 15/16" center to center screw holes Color: Antique Brass Active Set Includes: 1 Exterior Face Plate, 1 Interior Face Plate, 2 Handle levers, Key Cylinder (wiser keyway), latch & deadbolt set with 2 3/8" backset (over all length of latch and deadbolt set are 3 inch's), radius strike plates, spindle 9/32" SQ x 2 9/16", Mounting screws 10-32 TH x 2 7/16" Known Part Numbers: S4110, 1200-68, 55-226AB, 1200-67 Stamped On The Back of Face plate: PAT. NO. 4,671,089 - DES. 297,805 - 1200-68 - OTHER PAT. PEND. On latch PAT No. 4,671,089 and on dead bolt PAT NO: 4,741,089. 1200-67, Part Number 1200-3-1044, 8000-15-0, 8000-12, 1200-1-1021, 55-226AB Once our stock is gone this item will no longer be available. Sold AS IS - All sales are final.
$ 450.00$ 290.00
829 - Hoppe Split Shaft
Part Number: 829 Hoppe Split Shaft only screws sold separately (See Part Number: 840-031 Set Screws or S3004 - metric 6-10) Shaft Size Order By Length: 3 15/16 inch ( 5/16 inch x 3 15/16 inch or 8 mm x 100 mm) For Doors Smaller 1 3/4 inch thick Can be used as a replacement split shaft for old GU handle sets 4 21/64 inch (5/16 inch x 4 21/64 inch or 8mm x 110 mm) For Doors Smaller than 1 3/8 inch thick 4 11/16 inch (5/16 inch x 4 11/16 inch or 8 mm x 120 mm) For 1 3/4 Thick Doors Commonly used on Hurd and Truth hardware 5 1/2 inch (5/16 inch x 5 1/2 inch or 8 mm x 140mm) For 2 1/4" thick doors 6 1/4 inch (5/16 inch x 6 1/4 inch or 8 mm x 160 mm) used with the 1" Hoppe Handle extension part # 828 sold separately Commonly used on Hurd and Truth hardware that has extension 828 See figure F in drawing for correct split shaft spindle position installation. Associated Parts Sold Separately: 6 1/4 is used with the 1" Hoppe Handle extension part # 828 Part Number: 840-031 Set Screws pack Part number S3004 - metric 6-10 screws
$ 25.00
840-029 Amesbury Truth GU Handle Set Thumb Turn Plastic Washer set of 2 - Swinging Patio Door Hurd
840-029 Amesbury Truth GU Handle Set Thumb Turn Plastic Washer- set of 2 - Swinging Patio Door Hurd Comes with 2 plastic washers Two sizes available depending in your vintage of handle set. Large and small. Inside Diameter is the same on both. See picture of thumb turn that shows with 2 washers on it. One goes on the outside of the faceplate and the other goes on the inside of the faceplate. Discontinued Product. If it's in stock we have it. No returns all sales are final.
$ 8.00
D308 Mortise Lock Drive Rods Handset Spindles Shaft - Pack of 2
Part Number D308 Mortise Lock Drive Rods Handset Spindles Shaft Pack of 2 7 mm square x 18 mm long For Trilennium, W&F and Endura handle sets
$ 14.50
W&F Door Handle Solid Shaft
W&F Door Handle Solid Shaft Replacement Part Aluminum 1- 37/64" (40.1 mm) long x 9/32" (7.1 mm) tall Associated Parts Sold Sold Separately: Part Number 701 W&F Single Handle Bushing Kit W&F Interior and Exterior Replacement Handles W&F Door Handle Solid Shaft 870 - W&F Handle Extension
$ 8.00
834 - Hoppe Multi Point 3Pt Striker For Rollers - Auto
#834 - Hoppe 3Pt Striker For Rollers - Auto - Bright Brass Replacement Parts for Hoppe Multipoint Hardware used on swinging patio doors Known To have Been Used On: Hurd, Weather Sheild, Hoppe, Marvin BiltBest and many other door brands that used Hoppe Multi Point Hardware Sold Separately Are Part Numbers: #813 - Hoppe 3Pt Convert Auto Release Striker #833 - Hoppe 3Pt Convertible Under plate
$ 24.00
852-001 Dead Bolt For W&F Hurd Handle Set 1200 Series - discontinued see details for replacement option
***Discontinued Product. - see either link below to S4110 or 852 below for replacement handle options*** 852-001 Dead Bolt For W&F Hurd Handle Set 1200 Series NO LONGER AVAIABLE You will need to order replacement handed set: (Long Style available to order with handle set see part number S4110 5 1/2" center to center bore) Long Style available to order with handle set see part number 852 - Handle Set 6" Center to Center Bore No screws included use # 7 x 5/8" FHSMS Manufacturer: W&F Brand used on: Hurd, Peachtree, Weather Sheild and more Stamped on part is PAT NO 4,671,089 and 4,878,866 Discontinued Product.
$ 0.00
827 - Hoppe Back Plate Bushing
Part Number 827 - SOLD Individually Hoppe Backplate Bushing - (handle set or other parts not included) This Hoppe Backplate Bushing is for Hoppe Swinging Patio Doors System ONLY. Color: Clear Gold Opaque HANDLE BUSHING HFW F12 BACKPLATE MANUFACTURER: A/35/14 914 RL 750 16S 85 Used on Hurd handle set from 2004 and prior - See picture to match your handle set to correct bushing kit for Hurd DoorsThis Hoppe Backplate Bushing is for Swinging Patio Doors System ONLY.
$ 6.00
840-006 Amesbury Truth GU Handle Snap Ring Style - Swinging Patio Door
840-006 Amesbury Truth GU Handle Snap Ring Style - Swinging Patio Door. Replacement Door Handle only all other parts sold separately. Discontinued Product. What we have in stock is all that is available. No returns, all sales final, finishes color variation due to true metal finish and minor scratches.
$ 27.00
D302 W&F Trilennium Multipoint 6 Inch CTC Replacement Handle Set
Part Number: D302* W&F Trilennium 6 Inch CTC multipoint bore D302 is the new Replacement Handle Set - Non stock item special order - Allow 1-2 weeks for your order to ship (unless otherwise noted on our website about extended lead times) - No order cancellations or returns D302 is for doors with: 6 inch center to center 1 7/8" or 2 1/8" diameter bores and screw hole placement 5 3/16" Center To Center. Requires: 1 11/16" or 2 1/8" crossbore Model: D300 Standard Set** Screw Hole Placement: 5 3/16" Center To Center Size: for Door Thickness 1 3/4" or 2 1/4" Colors: Victorian Bronze, Satin Nickel, Bright Brass, Black Style: Active Standard 150 Degree- Has Thumb Turn, Keyed Cylinder and Lever is Operational*** For Single and French Active door panels. (Degree is how far the lever handle rotates for newer style multi point see pictures) Active Modified 180 Degree* - Has Thumb Turn, Keyed Cylinder and Lever is Operational*** For Single and French Active door panels. (Degree is how far the lever handle rotates for older multi point and double bore systems see pictures) Dummy - No Thumb Turn, No Key Cylinder and Fixed Lever**** For Inactive panels in French doors - that is fixed or has independent astragal installed Tumbturn for 3020 - Has Thumb Turn, No Key Cylinder and Fixed Lever**** For Inactive panels in French doors that has 3020 lock installed only*** Handing: Universal - Non handed works for both LH and RH swing doors Handle Sets have been known to have been used on Bayer, Pella, Peachtree and other door brands. Known W&F old handle set Pat No. 4,671,089 stamped on back of trim plate Notes for other options for this style hardware on older doors: D302 is manufactured for the current multipoint system and will work for you right out of the box - order Active Standard 150 Degree (see pictures). If you have older style multipoint or backset lock and dead bolt with 6” center to center bore and screw hole placement is 5 3/16" Center To Center then Active Modified 180 Degree (see pictures) If your door has a 6 inch center to center 2 1/8" standard double bore with back set latch and dead bolt and screw holes are also 6" center to center you need to order part number 852). If you are not sure what type of system your door has, please send us pictures of your handle set with the door panel open so we can see the hardware that the handle set connects to inside the panel. Email pictures to: info@windowpartscenter.com footnotes: Non stock - Estimated 1-2 week for your order to ship - No order cancellations or returns *Active Modified 180 Degree bushing or cartridge has no manufacture warranty Warranty claims are handled on a case by case bases by the manufacture. Pictures need to be emailed to info@windowpartscenter.com to submit a warranty claim for factory to review. This handle set also comes in other Models: See part numbers: D300, D301, D302, D304 ****Operational Lever: Can move up and down when door is unlocked Fixed Lever: Inactive, and is intended for push/pull function. Do NOT use a power driver tool to attach the handle set face plate retaining screws. Thread damage can result and is NOT considered a product defect. Associated Parts Sold Separately: S4112 - Peachtree Multipoint Mortise Lock Citadel IPD Citation For Trilennium Multi Point - Email us for quote. Info@WindowPartsCenter.com
$ 330.00 - $ 465.00
S4011 Hoppe Adjustable Door Hinge - Set Hinge- Non Removable Pin
Part Number: S4011 - SET Hinge Hoppe Adjustable Door Hinge Non Removable Hinge - Set Hinge Vertical Adjustment S4011 is Vertical Adjustment ONLY Watch video and read instructions in pictures (For Horizontal adjustment see part number S4012 Sold Separately and see hinge placement guide in picture) No Screws Included, sold individually Handing: Left Hand Hinge Used For: Left Hand In swinging (LHI) or Right Hand Out Swinging (RHO) Right Hand Hinge Used For: Right Hand In Swinging (RHI) Left Hand Out Swinging (LHO) SEE Hoppe "Application Diagram for Set Hinge” TO DETERMINE WHAT HANDING HINGE TO ORDER Pre-Order are Special order items, no returns Made out of Brass or Aluminum. Multiple finishes to choose from. Designed for a Greater Advantage • Adjusts vertically ( Use Set Hinge Part # S4011) and for horizontally ( see Guide Hinge Part # S4012) by 1/8" for a perfect swing. - see Installation Instructions page 1 number of hinges chart for application. • Brass hinges feature finial caps as shown • Aluminum hinges feature flush caps. • Large 3/16" hex head screws make adjustments effortless. Remove the finial in the set hinge to access the hex screw. • Single pass routing for quick and easy installation. • All Set and Guide Hinges are equipped with non-removable pins for security, making HOPPE Adjustable Hinges the ideal solution for both inswing and outswing doors. • Especially designed for larger doors, with a panel weight capacity of up to 330 lbs. Tested to a Higher Standard • Brass hinges are tested beyond an impressive 2.5 million cycles, in accordance with ANSI A156.1 Grade 1 – Commercial test procedures. • Backed by HOPPE's Limited Lifetime Mechanical Warranty. Finished with Superior Quality HOPPE's Brass and Aluminum Hinges are outstanding corrosion resistant materials HOPPE uses their Resista® Limited Lifetime Finish Warranty on four of their select premium finishes. The Aluminum Hinges have a high quality powder coating finish. Installation Set and Guide Hinge Placement: 3 Hinges Per Door Panel Up to 165 lbs: Starting at top of door Top of door Guide (Use Part# S4012) Set (Use Part# S4011) Guide (Use Part# S4012) 4 Hinges Per Door Panel Up To 165 lbs: Starting at top of door Top of door Guide (Use Part # S4012) Guide (Use Part # S4012) Set (Use Part# S4011) Guide (Use Part # S4012) 4 Hinge Per Door Panel 165-330 lbs Starting at top of door Top of door Guide (Use Part # S4012) Set (Use Part# S4011) Set (Use Part# S4011) Guide (Use Part # S4012) 5 Hinges Per Door Panel Up To 165-330 lbs: Starting at top of door Top of door Guide (Use Part # S4012) Guide (Use Part # S4012) Set (Use Part# S4011) Set (Use Part# S4011) Guide (Use Part # S4012) The Set hinge no matter what is always the 2nd from the bottom Pro Tip: Remove weight from the hinges by lifting up on the door before you adjust. Known to have been used on: Sierra Pacific Doors, Ashworth and many other
$ 55.00 - $ 130.00
840-005 Amesbury Truth GU Handle Snap Ring Style - Swinging Patio Door
840-005 Amesbury Truth GU Handle Snap Ring Style - Swinging Patio Door. Replacement Door Handle only all other parts sold separately. Discontinued Product. What we have in stock is all that is available. No returns, all sales final, finishes color variation due to true metal finish and minor scratches.
$ 27.00