Hurd Replacement Patio Door Handle Set Parts
137 Encore Tango Folding Handle and Operator Cover Kit 13342 12616
Part Number 137 Truth Amesbury Encore: Tango Folding Handle and Operator Cover for Casements and Awning Operators 13342 12616 Handing: Casements can be left or right handed See pictures above, video and Pro Tip below to determine handing you need to order for your operator. Awnings operators will always will be Left Hand. Colors: New Goldtone, Champagne (old Prior to 4/1/2024), Current Champagne (4/1/2024 to Present), Coppertone, Bronze, White, Black, Bright Brass, Polished Chrome, Brushed Chrome, Brushed Nickel, Antique Brass, Oil Rubbed Bronze, Beige Out of stock / Pre Order Colors can have a estimated 2-6 week lead time. Price depends on finish selected. Large QTY orders may not be eligible for returns. Pro Tip: Left Hand = White Bag to be used with Silver Worm Operator. Right Hand = Red Bag to be used with Gold Worm Operator. Encore Operators Sold Separately: Part Number: 119 Casement Encore Dual Arm Sill Mount Amesbury Truth Part Number: 147 AmesburyTruth Encore Sill Mount Casement Operator-Dyad Part Number: 158 AmesburyTruth Casement Sill Mount Operator-Encore-Single Arm Part Number: 207 Awning Amesbury Truth Encore Awning Sill Mount Operator. Proper Installation of an Operator Cover & Nested Folding Handle: When installing the cover and handle on the operator you should follow these instructions: • Snap the cover onto the operator base. • Place the handle onto the spline of the operator and rotate the handle to close the window. • Lock the window in place. • Rotate the handle ¼ turn back (towards opening direction) to reduce the pressure on the operator . • If the handle needs to be positioned in a nested cover you can remove the handle at this time and re-position it so that it will rest correctly in the nested cover. • Tighten the set screw on the handle. • Unlock the window and cycle the sash open and closed until the handle returns to the starting position whereby there is no additional torque required to close the sash. Note: the sash should travel to a point that the lock can easily engage and seal the window. • If the window does not come all the way into the closed position, and more force is required on the operator to close the window, you will need to review the window for the following; sash sag; racked window; lock points that are not properly aligned; or hinges not installed correctly. These issues should be corrected prior to repeating the installation of the handle onto the operator spline. Placing the operator and the handle under high stress and abusive loads can cause permanent failures to the handle or operator as the window is repeatedly opened and closed. This video will show how to determine which handing to 137 cover and handle to order for your operator: This video will show how to attached # 137 Encore Cover and handle to the # 119 Truth Encore Operator Manufacture Tech Note: Proper Installation of an Operator Cover & Nested Folding Handle. When installing the cover and handle on the operator you should follow theseinstructions:• Snap the cover onto the operator base.• Place the handle onto the spline of the operator and rotate the handle to closethe window.• Lock the window in place.• Rotate the handle Ľ turn back (towards opening direction) to reduce thepressure on the operator.• If the handle needs to be positioned in a nested cover you can remove thehandle at this time and re-position it so that it will rest correctly in the nestedcover.• Tighten the set screw on the handle.• Unlock the window and cycle the sash open and closed until the handle returnsto the starting position whereby there is no additional torque required to close the sash. Note: the sash should travel to a point that the lock can easily engageand seal the window.• If the window does not come all the way into the closed position, and more forceis required on the operator to close the window, you will need to review thewindow for the following; sash sag; racked window; lock points that are notproperly aligned; or hinges not installed correctly. These issues should becorrected prior to repeating the installation of the handle onto the operatorspline.Placing the operator and the handle under high stress and abusive loads can causepermanent failures to the handle or operator as the window is repeatedly opened andclosed. Known Part Numbers: 137, 096357, 096358, 096353, 096354, 096354, 096356, 13342 12616, HCSE54, MONCSE675 Known to have been used on the following brands: Hurd Operator cover and crank handle (nesting) for units manufactured 9/19/05 to present, Biltbest, Sierra pacific, Semco, Windsor, Lincoln, Comfort Line, Milgard, Fiber Frame, Monarch June 2006 to present and more
$ 25.00 - $ 67.00
701 W&F Single Handle Bushing Kit
Part Number: 701 Our Bushing is Metal and has been modified to meet 85 degree rotation needed for older handle sets.You can order a new handle set which comes with a bushing kit that we still have in stock - Part # 852For handle set from 2004 and prior - See picture to match your handle set to correct bushing kitThis Bushing Kit is for Swinging Patio Doors Double Bore System ONLY.This will rebuild one interior or one exterior bushing.Two kits are needed to rebuild the complete door handle.For instructions on how to replace Bushing Kit please click on our Blog Link: Window Parts Center Blog Known Brands: W&F, Hurd, Jeldwen, Caradco, Peachtree known number stamped on some handles: pat no 4,671,089 Associated Parts Sold Sold Separately: W&F Interior and Exterior Replacement Handles W&F Door Handle Solid Shaft 870 - W&F Handle Extension
$ 39.00
852 - Handle Set 6 inch Center to Center Bore
852 - Handle Set for 6" Center to Center Bore Colors: Bright Brass, Satin Nickel, Oil Rubbed Bronze*, Polished Chrome**, White** *Color AS IS: Oil Rubbed Bronze Type Finish (ORB). We will not accept returns on it for any reason for this finish. See finish note below. When you place your order for ORB you are agreeing to these terms for the ORB item. **Discontinued Colors: White and Polished Chrome. Once our stock is gone these colors will no longer be available Fits 2 1/8" Crossbore on 6" and 6 3/32" bore Centers. Can also be used on doors with 1 3/4" Crossbore. The lockset includes removable posts. 2 3/8" Back Set Mounting Screw Holes 6 1/16" center to center Durable Finish Fits Right or Left Hand doors East to install with Phillips screwdriver Known to work on Weather Shield, and Hurd Swinging Patio doors and replacement for W&F handle set with 6" Center to Center Bores. Tools Required for Install: Philips Screwdriver and Slotted Screwdriver. Detailed Installation Instructions Enclosed. Keyed and Keyed Alike: Standard: All handle sets come random Keyed with 2 Keys. You can order as Keyed Alike for a small upcharge per handle. For 2 or more handle sets you can have all of the handle sets come keyed the same. (Example if you order QTY 4 handle sets you will also need to add QTY 4 keyed alike to to your under found under accessory items) Allow an addition 1-2 weeks for keyed alike handle sets to ship We CAN NOT rekey handle sets to any existing keys you the customer may have for your home, you the customer would need to hire a lock smith for that. Known to have been used on: Replacement for Peachtree Part # 06200031. and is a replacement handle set for Hurd, Jeldwen, Caradco "Hallmark Leverset", and replacement handle for 6" center to center bore handle sets for Hurd, W&F Weather Sheild an more. Known Part Numbers: 1200, 12001-1, 1200-1, 40061999, PAT NO's 4,671,089 D295,829, 14421-WR. Part # 06200031 *Finish Notice For Oil Rubbed Bronze Type: Has NO manufacture warranty on finish wear. This product is sold AS IS and we will not accept returns on it for any reason. **Warning** Do NOT use a power driver tool to attach the handle set face plate retaining screws.Thread damage can result and is NOT considered a product defect. No returns will be accepted if when inspected product has thread damage and not in new condition. NOTE! 852 only works for 6 inch center to center bore and 6 1/16 inch center to center mounting screw holes, 2 1/8" standard double double bore with latch and dead bolt (see video and pictures with dimensions). (If you have the W&F multipoint hardware with 6 inch center to center 1 7/8" or 2 1/8" multipoint bore and screw holes are 5 3/16" center to center see part number: D300, D301, D302, D303, D304 or D305 ) *Additional Finish Manufacturer Warranty info: Warranty is for original consumer/purchaser Proof of product purchase is required. for Bright Brass, Stain Nickel and White only have a 1 year manufacturer warranty. Warranty does not cover normal wear and discoloration of Finishes, damage caused by scratches or abrasions, or any product that has been improperly installed, abused, worn out, altered or used for a purpose other than that for which it was intended, or used within 10 miles from the sea coast or body of salt water, or in a manner inconsistent with any instructions regarding its use or recommended care and maintenance, or that has been exposed to solvents, chemicals, or other harsh environments or foreign substances including any airborne foreign substances. Pricing subject to change - cannot retro active any pricing on previous orders or hold pricing for future orders.
$ 230.00 - $ 260.00
1200 Series Handle Set 6 inch Center to Center Bore (W&F Handle) - Discontinued See Details for replacement option
1200 series Handle Set 6" Center to Center Bore (W&F Handle) Discontinued No longer Available once our AS IS stock is gone Click Here to Replace with Part Number 852 Handle Set Handle Set 6" Center to Center Double Bore Condition: As Is - New product that is unused. Either: discontinued item and only what we have in stock is available, old stock, a customer return, vendor sample, or came in from the factory with finish flaws. May or may not have finish flaws or scratch’s. In some instances, these items are repackaged. Not available in all colors or handing. All sales final, No returns. If you can add to cart it is in stock. Old Style Handle Set is NLA (known number stamped on some old handles: pat no 4,671,089 D 295 829 Other Pat. Pending 1200-2-1). Part number 852 is the replacement style for the 6” center to center double bore backsets - dead bolt and latch. and Mounting screw holes of 6 1/16" center to center (see pictures & video below). W&F Replacement Parts Sold Sold Separately: W&F Interior and Exterior Replacement Handles W&F Door Handle Solid Shaft 870 - W&F Handle Extension 701 Bushing Kit NOTE! 852 only works for 6 inch center to center 2 1/8" standard double double bore with latch and dead bolt (see video below). (If you have the W&F multipoint hardware with 6 inch center to center 1 7/8" or 2 1/8" multipoint bore and screw holes are 5 3/16" center to center see part number: D300, D301, D302, D303, D304 or D305 ) *Additional Finish Manufacturer Warranty info: Warranty is for original consumer/purchaser Proof of product purchase is required. for Bright Brass, Stain Nickel and White only have a 1 year manufacturer warranty. Warranty does not cover normal wear and discoloration of Finishes, damage caused by scratches or abrasions, or any product that has been improperly installed, abused, worn out, altered or used for a purpose other than that for which it was intended, or used within 10 miles from the sea coast or body of salt water, or in a manner inconsistent with any instructions regarding its use or recommended care and maintenance, or that has been exposed to solvents, chemicals, or other harsh environments or foreign substances including any airborne foreign substances. Pricing subject to change - cannot retro active any pricing on previous orders or hold pricing for future orders.
$ 0.00
1200 Series W&F Handle Set 6 inch Center to Center Bore 1200 Series(Hurd Handle) Discontinued -See details for replacement option
This W&F Handle Set 6" Center to Center Bore (Hurd Handle) Discontinued No longer Available Click Here to Replace with Part Number 852 Handle Set Handle Set 6" Center to Center Double Bore Old Style Handle Set is NLA (known number stamped on some old handles: pat no 4,671,089 D 295 829 Other Pat. Pending 1200-2-1). Part number 852 is the replacement style for the 6” center to center double bore backsets - dead bolt and latch. and Mounting screw holes of 6 1/16" center to center (see pictures & video below). W&F Replacement Parts Sold Sold Separately: W&F Interior and Exterior Replacement Handles W&F Door Handle Solid Shaft 870 - W&F Handle Extension 701 Bushing Kit NOTE! 852 only works for 6 inch center to center 2 1/8" standard double double bore with latch and dead bolt (see video below). (If you have the W&F multipoint hardware with 6 inch center to center 1 7/8" or 2 1/8" multipoint bore and screw holes are 5 3/16" center to center see part number: D300, D301, D302, D303, D304 or D305 ) *Additional Finish Manufacturer Warranty info: Warranty is for original consumer/purchaser Proof of product purchase is required. for Bright Brass, Stain Nickel and White only have a 1 year manufacturer warranty. Warranty does not cover normal wear and discoloration of Finishes, damage caused by scratches or abrasions, or any product that has been improperly installed, abused, worn out, altered or used for a purpose other than that for which it was intended, or used within 10 miles from the sea coast or body of salt water, or in a manner inconsistent with any instructions regarding its use or recommended care and maintenance, or that has been exposed to solvents, chemicals, or other harsh environments or foreign substances including any airborne foreign substances. Pricing subject to change - cannot retro active any pricing on previous orders or hold pricing for future orders.
$ 0.00
825 Hoppe Single Point Gear Box
Part Number 825 Hoppe Single Point Gear Box as shown in pictures and in product video **** 825 Single point gear box is not interchangeable with multi point gear box system interior components are different see video**** In stock: Only part # 825-D which has a 1 3/4" Backset and 1" Dead Bolt Throw Special Order: All other part numbers are special order items (no returns or order cancellations) and can have a 1-4 week lead time once you place your order. Handing: Non handed - Strike is reversible for both left hand and right hand doors (see video below or revering latch instructions) Install Instructions: Remove set screws on handle levers and remove Remove mounting screws on faceplate estuation of the handle set On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the gear box (keep all screws you will reuse them) Install new multipoint with screws Test for Operation Reinstall handle set Test for proper operation
$ 97.00 - $ 125.00
131 Amesbury Truth Folding Handle for Casement and Awning Operator 11/32 Inch Spline
Part Number: 131 Folding Crank Handle for Amesbury Truth 11/32 Spline OperatorsColors: Aluminum, Beige, Black, Bright White, Bronze, Chestnut Bronze, Clay, Faux Oil Rubbed Bronze, New Goldtone, Tuscan Bronze White Special order Colors: Goldtone, Oil Rubbed Bronze, Bright Brass are a non returnable item- no returns for these items Large Quantities Order: orders with QTY 50 or more are special order items no returns or order cancellations. Related Parts: Part # 101 Truth Maxim Dual Arm Casement Operator Part # 102 Truth Maxim Split Arm Dyad Casement Operator Part # 209 Truth Maxim Awning Operator Part # 111 Truth Ellipse Style Split Arm Dyad Casement Operator Part # 105 Truth Ellipse Style Straight Arm Casement Operator Other Amesbury Truth Operators Part # 131 Folding Handle was primarily used on Part # 101, 102 and 209 Truth Maxim casement and awning operators). Replacement part for Hurd Casement and awing window operators Vintage Classic Style: 02/02/1998 - 9/17/2007. Also used on many other window brands that use Truth Hardware Known Part Numbers: Truth, 45393, U.S. PAT. 351490, 5560082, 131, Truth 3, 037189, 037188, 091691, 11329-32, HCSE31, A3-2104, A4-2149, A4-2150, A4-2147, A4-2148, 00-0000 Replacement Parts for: Hurd, Semco, Marvin, Cascade, Caradco, BiltBest, Milgard, Sierra Pacific, Vetter, Allsco and more. Updated 7/24/23
$ 27.00 - $ 145.00
522 C Elite Handle Set - Offset Latch
Part Number 522 Sash Controls C Elite Keyed Handle Set with Offset Latch - Sash Controls Face plate is 8 1/2" long x 1" wide (new style) Handle 5 1/2" Center to Center (CTC). Screw Holes are 3 15/16" Center to Center (CTC). (For Center Latch Style Handle Set see part # S3006) 2265 can be stamped on back of plate. Mortise lock box sold separately. Tailpiece can be cut to fit multiple thickness doors. (We cannot accept returns if the tailpiece has been cut). Style (Function): Non-keyed, Keyed and Dummy Non-Keyed handle sets: Means you can lock and unlock your door only from the inside with the lock latch. But you can NOT lock or unlock from the outside. Most Colors are a stock item. Keyed handle sets: Keyed Means you can Lock and Unlock your door from the inside using the lock latch AND Lock and Unlock your door from the outside using a key. Most Colors are a stock item. Shafts for the keyed lock may need to be cut depending on your thickness of door your have. Otherwise handle will be loose on your door. If you want to avoid the possibility of having to cut the shafts order the NON KEYED version. (see trouble shooting install at bottom of page for more details on cutting shafts). Also see instructions that come with the handle set that is also pictured above Dummy Handle Sets: No Locking or unlocking capability. Used mostly on 4 wide doors where 2 panels operate. Dummys are mounted on the secondary door. Allow 3-4 week lead time once order is placed. Dummy Handle sets DO NOT need a new Mortise lock! Most colors are stocked. If a product is not in stock allow a 2-5 week lead time once order is placed. We will notify you on lead time if a product is not in stock. If your Recessed Mortise Lock has the 90 degree black cylinder you will need to purchase a new recessed mortise lock part # 518, S3007 or #S3011 with the 45 degree gray/silver cylinder for this handle set to work. Both mortise box work with handle # 522 so you will need to choose the type that your door panel is machine prepped for. Associated Products Sold Separately: Part Number: 518 Mortise Lock Part Number: S3011 Mortise Lock Box Part Number: S3007 Mortise Lock Box Part number S3006 For Center Latch Version Handle Set Trouble Shooting Install:If when using they keyed handle set and the turn lever for the lock and the turn lever for the keyed cylinder are hitting and pushing each other out of the the latch: This could be because you have the french style Hurd door and the panel is a different thickness. What you will need to do is cut the shafts so they both can fit into the mortise lock and the handle set can be screwed down tightly. Easiest is to put on the outside handle in place and mark the shaft where it comes through. Take it off and do the same for the inside handle. Then, you can cut just shy of that mark on both shafts and then they should meet in the middle. Double check your marks so you cut on the correct side and don't cut too short. This handle set is made as a replacement option for many door thicknesses, which is why you get multiple length screws and can cut the shafts to fit. If you want to avoid doing this all together order the non keyed version. Also, see instructions that come with the handle set that are also pictured above. Never use power tools when installing handle sets you run the risk of stripping out the screws. If you are using the 522 to replace the Old Hurd Wood and Brass Handle Set 516 for how to videos and full instructions please click here for how to page.
$ 76.00 - $ 430.00
516 - W&F Upgrade Handle Handle Set Brass and Wood Handle - See Description to Order Replacement Option
516 - W&F Upgrade Handle (Brass and Wood) Is No Longer Available. Use replacement options below. How to order replacement handle set - please read all instructions below, view pictures and watch our how to videos before you place your order! Verify you have the "A" screw hole position on your W&F mounting plate (see picture) Please watch videos below! Pictures and video show a Hurd Classic Sliding Patio Doors that Used W&F Brass and Wood handle Set. If you find you have the "B" Screw Hole Click Here Parts to order: 1. Handle set: Part Number 522 Handle Set offset latch for "A" Screw Hole Position. Your choice of function: Non keyed, Keyed or Dummy - see additional details for function explanation. 2. Mortise Lock: Remove your mortise lock from your door to see what you have! The W&F handle set used a 90 degree cylinder which does not work with the 522 handle set. You will need to replace the mortise lock box with a 45 degree cylinder mortise lock box. Depending on your door manufacture you need one of the following # 518 Gray cylinder 45 degree (Hurd Brand Doors and others) # S3007 45 Degree (other brand doors) #S3011 45 Degree (other brand doors) If your mortise lock box does not look like any of the above please email us picture's before you place your order so we can help you find the correct parts. 3. Binding Post Screw - as shown in the how to video the 522 handle set is not as long as the old W&F handle set you are replacing. You will have to fill the top screw hole that will be left over from the old handle set. Easiest solution to this is to use a Binding Post Screw. Part# 546 - your choice of finish 4. White Shim - as shown in how to video you door thickness may require a shim. Shim is known to be needed on Hurd Doors Part Number: 522SHIM Additional Info: 522 Handle Set Function Explanation: Non-Keyed: Means you can lock and unlock your door only from the inside with the lock latch. But you can NOT lock or unlock from the outside. Most Colors are a stock item. Keyed: Keyed Means you can Lock and Unlock your door from the inside using the lock latch AND Lock and Unlock your door from the outside using a key. Most Colors are a stock item. Shafts for the keyed lock may need to be cut depending on your thickness of door you have. Otherwise handle will be loose on your door (see instructions that come with the handle set that is also pictured above). If you want to avoid the possibility of having to cut the shafts order the NON KEYED version. (see trouble shooting install at bottom of page for more details on cutting shafts) Dummy: No Locking or unlocking capability. Used mostly on 4 wide doors where 2 panels operate. Dummy's are mounted on the secondary door. Dummy Handle set DO NOT need new Mortise lock as there is no locking feature! Trouble Shooting Install:If when using they keyed handle set and the turn lever for the lock and the turn lever for the keyed cylinder are hitting and pushing each other out of the latch: This could be because you have the French style Hurd door and the panel is a different thickness. What you will need to do is cut the shafts so they both can fit into the mortise lock and the handle set can be screwed down tightly. Easiest is to put on the outside handle in place and mark the shaft where it comes through. Take it off and do the same for the inside handle. Then you can cut just shy of that mark on both shafts and then they should meet in the middle. Double check your marks so you cut on the correct side and don't cut too short. This handle set is made as a replacement option for many door thickness which is why you get multiple length screws and can cut the shafts to fit. If you want to avoid doing this all together order the non keyed version. See instructions that come with the handle set that is also pictured aboveNever use power tools when installing handle sets you run the risk of stripping out the screws. Known Part Numbers On W&F Handle : P/N 120-50, PAT. # 5,092,114 Mounting Plate Known part Numbers: 011771, P/N 120-60; PAT. # 5,092,144 If your mounting plate and handle uses the "B" Screw Holes See Part Number S3006 Replacement Kit
$ 0.00
855 GU Active Single Point Gear Box 45-92-8
Part Number 855 Single Point GU Gear Box Hardware* Schlosskasten Security / Schlossk. Sec. *Single point gear box is not interchangeable with multi point gear box system interior components are different. For Swinging Patio Doors Depending on vintage your sticker label color can be orange or white with the following numbers: Orange Label: 6-29377-45-0-1 A 45-92-8 or 45-92-8 EINST. White Label: 6-29377-45-0-1 B Scholssk.Sec.U 45/92/8 Handing: Strike is reversible for both left hand and right hand doors. See video on how to reverse the latch Brands known to been used on: GU, Hurd, Sierra Pacific and More. Install Instructions: Remove set screws on handle levers and remove Remove mounting screws on faceplate estuation of the handle set On side of door remove screw that lines up with the lock cylinder. Remove the handle set Remove all screws down the side of the door that holds on the gear box (keep all screws you will reuse them) Install new multipoint with screws Test for Operation Reinstall handle set Test for proper operation *Single point gear box is not interchangeable with multi point gear box system interior components are different. updated 7/18/23
$ 115.00
544 -AmesburyTruth Signature Style Handle Set Two Point Locking For Sliding Patio Door
Part Number 544 Amesbury Truth Signature Style Handle Set Two Point Locking For Sliding Patio Door Signature Style Handle Set 40.94 and 40.68- Truth (mortise lock box and keeper not included) Model: Standard 40.94 - contour shape which is both elegant in style and easy to grasp. Contemporary 40.68 - sleek modern design resulting in a contemporary look that is sure to compliment your door system. (If replacing 40.68 on existing door with 40.94 with dual mortise lock you will need to purchase Contemporary style keeper sold separately) Style: Active with key - handle set comes with 2 keys and keyed cylinder, for exterior locking and unlocking capability. Dummy - for 4 wide sliding patio doors, secondary panel. no locking capability. Product Used On Hurd Energy Saver Sliding Patio Door. Direct replacement for Old style Energy Saver Handle Set #501Special Order Item - No Returns - lead time 2-3 weeks.NOTE: Part # 501 Handle set that is a Truth part and used on Hurd Energy Saver Sliding patio doors was used up until about February 2014. The Current handle set is called their Signature Style #544 and is slightly different from the #501. However they are interchangeable and # 544 will work on your door. Some staining or touch up may be required but screw holes are the same. Related Product Sold Separately: Mortise Box and Keeper for Old Style 501 Handle Set: Used with Part # 555 - Amesbury Truth 2 Point Recessed Mortise Lock & Keeper Kit Current Style Mortise box part number 558 Current Style Keeper Part Number C1059 40.94 Contemporary style keeper sold separately
$ 149.99 - $ 389.99
518 Surface Mount Single Point Mortise Lock
Part # 518 Replacement Door Mortise Lock for sliding Patio door Cylinder Color Style and Degree: Gray Style= 45 Degree Cylinder with faceplate Face Plate Over All Dimensions: 6 1/8" Long x 3/4" Wide Face Plate Top and Bottom mounting Screw Holes Center To Center Dimensions: 5-3/8" overall depth 1-5/32 inch Black Style = 90 Degree Cylinder - will not come with faceplate customer will need to reuse their old one You must replace the mortise lock with the same version (you can usually determine this as the old cylinder where colored either Gray or Black. The angle of the Gray cylinder is at a 45 degree angle and the black is at a 90 degree angle) If you do not choose the correct one keyed cylinder will not fit/operate. If your Cylinder is silver or gold looking color you have the newer style determine which style you need by the slot degree inside the cylinder (see drawing for example the 45 degree cylinder) Manufacturer: W&F Known Manufacturing Brands Used on: Hurd, Peachtree, W&F *replacement and more Similar Looking Products With Different Dimensions: Part Number C1033
$ 47.00